Manual AEG CM6-1-5ST Gourmet 6 Cafetieră

Manual

1. Clean the filter insert and the glass jug after every

use with mild detergent and warm water or in the

dishwasher.

2. If necessary, wipe down the coffee bean compartment

(2) and the lid (1) with a damp cloth.

3. Wipe down the housing with a damp cloth. If necessary,

use a little mild detergent to remove more intense soiling.

Cleaning the Grinder Shaft

1. Remove the coffee beans from the coffee bean

compartment (2). (Apart from the few beans that you

cannot reach by hand.)

2. Insert a paper filter into the filter insert.

3. Press the button (18) to switch on the device.

The grinding process will start.

4. Once the rest of the coffee beans have been

ground - you can tell this from the change in the

grinding noise – stop the grinding process by pressing

the button (26) again.

5. Take out the coffee bean compartment: To do this, turn

it a little anticlockwise until it disengages. Lift it off.

6. Move the grinding fineness dial (8) to the OPEN

position.

7. Pull out the top part of the grinder (3) by the small

handle.

8. Clean the grinder shaft and the grinder with the

cleaning brush that is supplied.

9. Reinsert the top part of the grinder and press it down.

Make sure it is in the correct position (arrow marking).

Fold the handle down again.

10. Adjust the grinding fineness dial back to a grinding

fineness. The grinder is locked again.

11. Place on the coffee bean compartment at an angle and

turn it clockwise a little until it engages.

12. Open the filter compartment (5) to remove the paper

filter.

13. To clean the grinder shaft from below: Press the

button (19) until the symbol occurs. Press the button

(18). The coffee powder tunnel gate will open. Open the

filter compartment, use the brush to clean the residue

inside, close the filter compartment, press the button (26)

to close the coffee powder tunnel gate.

Descaling

As a precaution we recommend descaling after 60 uses.

Use only environmentally friendly descaling agent and

always follow the manufacturer´s instructions.

Fill the water tank with water and descaling agent. Place

the jug with lid on the warming place. Wait 15 minutes

then press descaling button and press START to

start the appliance. Let the water run through. Perform

two more brewing cycles with water only to allow

appliance to rinse through properly.

If the brewing process is to be aborted prematurely,

press the button (26). The operating lamp goes out and

the device will abort the brewing process.

Making Coffee with Coffee Powder

1. Fill the water tank.

2. Open the filter compartment and insert a paper filter.

Add the quantity of coffee powder you want. Close the

filter compartment.

3. Set the desired number of cups with the button .

4. Press the button. The symbol (14) appears on

the display.

5. Press the button (18) to start the brewing process.

If the brewing process is to be aborted prematurely,

press the button (26). The operating lamp goes out and

the device will abort the brewing process.

Making coffee with a pre-set time

To make coffee with a pre-set time, the clock needs to be

set (see “Setting the time”).

1. Make preparations according to your preference, coffee

beans or coffee powder. Pour in water and insert a filter.

2. Set the desired number of cups with the button .

3. For making coffee with coffee powder, press the

button before the timer is set.

The symbol (14) appears on the display.

4. Press the timer button until the indicator time (16)

flashes on the display.

5. Use the and buttons to set the start time you

want. For making coffee with coffee beans, use the button

(24) to set the coffee strength you want.

6. To activate the pre-set time, press the start button

again. The symbol (15) appears on the display.

The pre-set time is activated.

Once the pre-set time is reached, the device switches on

automatically. The operating lamp lights up and the (17)

symbol flashes on the display.

Deactivating the pre-set time

To deactivate the pre-set time setting, press the

CANCEL button (26). The symbol (15) goes out and the

programming is deactivated. However, the pre-set time is

retained and can be reactivated at any time until a new

pre-set time is programmed or the device has been

disconnected from the power supply.

Cleaning and Care

Do not use any toxic, corrosive or abrasive cleaning

agents or scouring sponges to clean the device.

These can damage the surface.

EN

DE

BG

ES

GR

FR

NL

PT

EN

DE

BG

ES

GR

FR

NL

PT

Setting the Number of Cups

Keep pressing the button until the display (7) shows

the number of cups you want (12).

The selected number of cups is saved until a new number

of cups is set or the device has been disconnected from

the power supply. All of the water in the water tank is

always used up, regardless of the set number of cups or

coffee strength.

Setting the Coffee Strength

The coffee strength can be set when making coffee with

coffee beans. To do this, keep pressing the button (24)

until the coffee strength (13) you want is shown on the

display.

- Mild coffee

- Medium coffee

- Strong coffee

The selected coffee strength is saved until a new coffee

strength is set or the device has been disconnected

from the power supply.

Keep-Warm Function

The device has an automatic keep-warm function. The

hotplate remains switched on for 40 minutes after each

brewing process. After the brewing process the keep

warm icon (17a) in the display will be lit. To end the

keep-warm function prematurely, press the button (26)

to cancel.

Drip Stop

The device has a drip stop which prevents coffee from

dripping out of the filter when the jug has been removed

from the device. When the device is in operation, the filter

compartment (5) must be closed and the jug with lid

placed must be placed beneath the filter compartment.

During the brewing process, the jug must not be removed

from the device for longer than 30 seconds as otherwise

the filter could overflow.

Preparation

Making coffee with coffee beans

1. Fill the water tank.

2. Fill the coffee bean compartment.

3. Set the grinding fineness you want.

4. Open the filter compartment and insert a paper filter.

Close the filter compartment.

5. Set the desired number of cups by pressing .

6. Set the desired coffee strength with the button .

7. Press the button (18) to switch on the grinder and start

the brewing process.

6

1

2

8

3

4

7

9

10

11

5

19 20 21 22 23 24 2625

16

15

13 12

17

17b

17a

14

18

Components

1. Lid for the coffee bean compartment

2. Coffee bean compartment

3. Grinder (top part removable)

4. Control panel

5. Filter compartment

5a. Filter insert

6. Glass jug with lid

7. Display

8. Grinding fineness dial

9. Water tank lid

10. Fill-level indicator

11. Water tank

12. Indicator number of cups

13. Indicator coffee strength

14. Indicator coffee powder

15. Indicator timer

16. Indicator time

17. Indicator operation (flashing)

17a. Indicator keep warm-function

18. start button with operating lamp

19. Descaling/cleaning of shaft

20. Setting pre-set time

21. Setting the hours

22. Setting the minutes

23. Setting the number of cups

24. Setting coffee strength

25. Making coffee with coffee powder

26. Cancel button

Getting started

Wipe the device with a clean, damp cloth. Rinse the glass

jug (6) and the filter insert (5a) with a little mild

detergent and water.

Prior to preparing coffee for the first time, perform one

brew with water only. Fill the freshwater tank up to the

top cup marking with cold water. Close the lid. Press

to start the appliance. Allow the water to flow through

into the coffee jug. When brewing is finished, empty the

coffee jug.

Handling and Operation

Setting the time

As soon as the appliance is plugged into a socket, the

display lighting turns on and the time display

12:00 flashes. The clock has a 24-hour time format.

Set the hours by long pressing;

For both hours & minutes.

1. Keep the button pressed to set the hours (21).

2. Keep the button pressed to set the minutes (22).

The time is saved until a new time is set or the device has

been disconnected from the power supply.

Filling the water tank

1. Open the water tank lid (9).

2. Pour the quantity of water required for the

number of cups you want (maximum 10 cups) into the

water tank (11).

3. Close the water tank lid.

Adding coffee beans

1. Take off the lid of the coffee bean compartment (1).

Ensure that the water tank is closed so that no coffee

beans can fall into the water tank.

2. Fill the coffee bean compartment (2) with coffee beans.

Do not overfill.

3. Place the lid back on the coffee bean compartment.

Setting the Grinding Fineness

Move the dial for the grinding fineness (8) to the position

you want fine/medium/coarse.

When you switch to another grinding strength, there will

still be coffee powder with the previous grinding strength

in the grinder shaft. The grinder shaft may need to be

cleaned beforehand. (see chapter Cleaning the Grinder

Shaft)

Inserting the Filter

1. Open the filter compartment (5).

2. Insert a paper filter into the filter compartment (5a).

Close the filter compartment. It must engage.

5a

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru AEG CM6-1-5ST Gourmet 6 Cafetieră. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați AEG. S-ar putea să ofere un manual original. Căutați manualul dvs. AEG CM6-1-5ST Gourmet 6 Cafetieră într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru AEG Cafetiere
Mai multe manuale pentru Cafetiere

Întrebări frecvente despre AEG CM6-1-5ST Gourmet 6 Cafetieră

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.