Manual Auriol IAN 55982 Stație meteo

Manual

7 GB/CY

Before Initial Use

j Do not place the devices near sources of in-

terference such as television sets, computers,

thick walls, thermopane windows etc. Other-

wise the transmission of radio waves between

the devices may be impaired.

j Please install the devices at least 2 metres

away from sources of interference. Otherwise

the transmission of radio waves between the

devices may be severely impaired.

j Please ensure that neighbouring devices are not

operated at the same frequency of 433 MHz.

Such devices may cause interference to the

radio connection.

j Do not place the devices next to or on metal

plates. Otherwise the quality of radio wave

transmission may be reduced.

j Do not install the devices in buildings made

of reinforced concrete, e.g. airports, high-rise

buildings, factories or cellars. Otherwise the

transmission of the radio waves between the

devices may be severely impaired.

j Do not start reception of the waves in a moving

vehicle, e.g. car or train. The transmission of

the radio waves to the devices may interfere

with the electronics of the vehicles.

j In open spaces do not place the devices more

than 25 metres apart, as otherwise transmission

of the radio waves may be interrupted.

j Do not expose the devices to temperatures

below –20 °C for prolonged periods, as

otherwise this will adversely affect the trans-

mission range.

Q

Putting the Outdoor

Sensor into Operation

Removing the battery safety strip:

Note: For this procedure you need a flat-blade

screwdriver.

j Open the battery compartment cover on the

rear of the outdoor sensor by turning the

screw in an anticlockwise direction with the

flat-blade screwdriver.

j Remove the battery safety strip. The outdoor

sensor is now ready for operation and the

control LED

36

lights up briefly.

j Close the battery compartment cover and

tighten the screw in a clockwise direction.

Installing the Outdoor Sensor:

Note: For this step you need a drill.

CAUTION! DANGER OF DEATH

AND INJURY AND DANGER OF

MATERIAL DAMAGE! Please read

the operating and safety instructions of your drill

through carefully.

j

Find an appropriate place for the outdoor sensor.

Note: Please ensure that you install the

outdoor sensor within a radius of 25 m from

the weather station. Check that there are no

obstacles between the outdoor sensor and

the weather station. Otherwise there may be

interference of the transmission of data.

For wall mounting:

j Mark the drill hole on the wall.

j Drill the hole with a drill.

j Insert a suitable wall plug into the drill hole.

j Use a screwdriver to insert a suitable screw.

j Hang the outdoor sensor on the screw with

the wall mounting hole

38

.

For free standing:

j Turn the stand

43

out from the bottom of the

outdoor sensor.

Q

Putting the Weather

Station into Operation

Removing the battery safety strip:

j Open the battery compartment

34

on the

back of the weather station.

j Pull out the battery safety strip.

j Then close the battery compartment

34

.

j Press the RESET button

33

. All of the symbols

light up briefly.

As soon as the battery safety strip has been

removed, the weather station starts to receive

the radio signal.

Note: Do not change the location of the weath-

er station during reception. Otherwise there may

be interference.

For wall mounting:

j Mark the drill hole on the wall.

j Drill the hole with a drill.

j Insert a suitable wall plug into the drill hole.

j Use a screwdriver to insert a suitable screw.

j Hang the weather station on the screw with

the wall mounting hole

32

.

For free standing:

j Turn the stand

35

out from the bottom of the

weather station.

Connecting the weather station with the

outdoor sensor and the DCF radio signal:

After removal of the battery safety strip the weather

station attempts to establish a connection with

the outdoor sensor. This process may take a few

minutes. When the connection with the outdoor

sensor has been successfully established, the

selected channel symbol

22

is shown the channel

of the outdoor sensor (To change the channel of

the sensor, see “Setting the channel”). If the con-

nection with the outdoor sensor is not established

automatically, this can be done manually by

pressing TX button

42

of the sensor”.

As soon as the weather station has established a

connection with the outdoor sensor it automatically

begins to receive the DCF radio signal. This proce-

dure takes a few minutes and is shown in the LC

display by the flashing radio tower symbol

18

.

When the DCF radio signal is being successfully

received, the radio tower symbol

18

is shown

permanently in the display. If at the time of putting

the device into operation it is not possible to syn-

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Auriol IAN 55982 Stație meteo. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Auriol. S-ar putea să ofere un manual original. Căutați manualul dvs. Auriol IAN 55982 Stație meteo într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Auriol Stații meteo
Mai multe manuale pentru Stații meteo

Întrebări frecvente despre Auriol IAN 55982 Stație meteo

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Auriol IAN 300037 Stație meteo

Manual

Auriol IAN 311249 Stație meteo

Manual

Auriol IAN 71010 Stație meteo

Manual

Auriol IAN 300120 Stație meteo

Manual

Auriol IAN 321304 Stație meteo

Manual

Auriol IAN 466444 Stație meteo

Manual

Auriol IAN 77437 Stație meteo

Manual

Auriol IAN 365202 Stație meteo

Categorii relevante