Manual Avenido AV 1310 Fierbător

Manual

6

G. Temperature setting button - 5℃

H. Temperature hold button

BEFORE FIRST USE

Fill the kettle with water three times to the maximum level boil and pour out. To remove any factory odor.

Touch the buttons on the touch panel (8) only with your fingertips, touching with your fingernails may damage the panel !

BASIC OPERATION: SINGLE BOIL TO 100℃

1. Set the base (5) on a stable, flat and heat-resistant surface.

2. Fill the kettle with water so that the water level is between the maximum and minimum levels on the water level indicator in the

center of the kettle.

3. Remember to close the kettle's lid (1) after filling, otherwise the kettle will not turn off automatically when the water boils.

4. Plug the power cord plug into a 220-240V ~50/60Hz grounded power outlet. Place the kettle on the base (5), you will hear a "di"

sound, the touch panel (8) will light up, and the LCD display (2) will indicate the current water temperature.

5. Press the (A) "On/Off" button, the (H) temperature hold indicator and the "+"(F), "-" (G) indicator will light up, and the heater will

start heating water, the LCD display (2) will start to indicate the current water temperature. The water temperature will increase until

boiling, that is, up to 100°C.

6. After the water boils, the kettle will automatically turn off, you will hear a "di-di" sound twice.

The LCD display (2) will indicate 100°C then after 25 seconds it will turn off and the icon (A) On/off will flash.

7. Want to turn off the kettle before the water is finished boiling, lift it from the base (5) or press the On/Off button (A).

8. You can start turning the kettle on again about 2 minutes after the last use, for this purpose press the (A) "On/Off" button.

The kettle also has a function to set the temperature from 40℃ to 100℃ in 5 ℃ increments, to do this, use the F(+) and G (-)

buttons to increase the F (+) temperature or decrease the G (-) temperature.

ADVANCED OPERATION: BOIL WATER TO THE SELECTED TEMPERATURE OF 40℃, 70℃, 80℃, 90℃

Place the kettle on the stand (5), you will hear a "di" sound. Press the temperature selection button 40℃ (B), 70℃ (C), 80℃ (D) or

90℃ (E), the LCD display (2) will show your selected temperature of 40℃, 70℃, 80℃ or 90℃, then the LCD display (2) will show

the current water temperature inside the kettle.

The temperature hold indicator (H) and On/off indicator (A) will light up, and the heater will start heating the water,

The kettle will stop boiling water when the selected temperature level reaches 40℃, 70℃, 80℃, 90℃, you will hear "dii-di" sound

twice.

The LCD display (2) will indicate the temperature reached, then after 25 seconds it will turn off and the indicator (A) On/Off will

flash.

If you want to turn off the kettle before the water has finished boiling, lift it from the base (5) or press the On/Off button (A).

You can start turning the kettle on again about 2 minutes after the last use, for this purpose press the (A) "On/Off" button.

TEMEPRATURE HOLDING FUNCTION

Place the kettle on the stand (5), you will hear a "di" sound. Press one of the temperature selector buttons on the auxiliary panel

(8), then press the temperature hold button (H), the indicator (H) will start flashing, this means that the temperature hold function is

on.

After reaching the set temperature, the kettle will enter the temperature hold mode and will cycle the water when the water

temperature drops by 5℃ from the selected temperature level.

If the water temperature in the kettle is higher than the desired temperature (more than 5℃), the temperature hold function

indicator (G),will flash until the water cools down to the pre-set temperature, being in temperature hold mode all the time.

To interrupt the temperature hold function, remove the kettle from the base (5) or press the button (A). The temperature hold

function is maintained for 2 hours after the last boil.

SAFETY FEATURES

The appliance is equipped with an automatic overheat fuse, the fuse will activate when it has been used with insufficient water.

Always make sure that the amount of water in the appliance is above the minimum level. If the fuse engages, turn off the kettle by

pressing button (A), then remove the plug from the power outlet and let the kettle cool down for 5-10 minutes. Then fill the kettle

with water and turn on the appliance, which will operate normally.

Turning on an empty kettle or one insufficiently filled with insufficient water will automatically turn off the device. In this case, wait

several minutes. Pour the appropriate amount of water and turn the kettle on again.

Do not leave the switched-on kettle unattended.

The kettle is an electrical appliance not designed to hold water or any other liquids. After boiling the water, pour it immediately into

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Avenido AV 1310 Fierbător. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Avenido. S-ar putea să ofere un manual original. Căutați manualul dvs. Avenido AV 1310 Fierbător într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Avenido Fierbătoare
Mai multe manuale pentru Fierbătoare

Întrebări frecvente despre Avenido AV 1310 Fierbător

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Avenido AV 1309 Fierbător

Manual

First Austria FA-5405-9 Fierbător

Manual

Midea MK-17G03A Fierbător

Manual

Gorenje K17OGP Fierbător

Manual

Zelmer ZCK7632 Fierbător

Manual

Zelmer ZCK7950 Fierbător

Manual

Zelmer ZCK7924 Fierbător

Manual

First Austria FA-5409-6 Fierbător

Categorii relevante