Manual Dremel 2000 Versatip Sculă electrică multifuncţională

Manual

GB

6

ignition. When this is not the case, repeat steps 1 and 2.

When the Dremel Versatip is cold, ignition might cause a

short whistling sound. This is normal and does not mean

there is something wrong with the tool.

* Note: the flame guard must be installed correctly, for the tool

to be able to ignite.

When the ignition switch is released, the flow of gas is

automatically shut off, causing the Dremel Versatip to stop

and slowly cool down. To continuously operate the Dremel

Versatip, follow the steps in figures 2, 3 and 4. To switch the

Dremel Versatip off, let go of the ignition switch and move the

lock button to the right (figure 5). This will immediately stop

the flow of butane gas.

USING WITH AN OPEN FLAME

To use the Dremel Versatip with an open flame, unscrew the

flame guard, remove the catalyst (and tip if attached) and

screw flame guard back onto the tool and securely tighten the

flame guard nut.

FLAME LENGTH AND TEMPERATURE ADJUSTMENT

After ignition, make sure the tool is on by checking that the

catalyst starts to glow. Then move the flame control lever to

the right to increase flame length and temperature, or to the

left to decrease flame length and temperature. When using the

open flame or hot air the Dremel Versatip is at the correct

temperature immediately after ignition. Please allow 25 seconds

of heat up time for tips.

INSTALLING OR CHANGING TIPS

ALWAYS ALLOW THE TOOL TO COOL

FULLY BEFORE REMOVING OR

REPLACING TIPS.

Make sure to use the right tip for the job you want to do. Only

use tips that fit onto the tool perfectly. Loose fitting tips might

result in an uncontrolled and unsafe flame.

The use of tips requires the catalyst to be installed. To install

the catalyst unscrew the flame guard nut and remove the

flame guard. Slide in the catalyst into the flame guard with the

narrow part facing outward. Place the flame guard and catalyst

back on to the tool and securely tighten the flame guard nut.

The soldering tip, cutting knife tip, shaping knife tip and hot

blower tip can be screwed onto the catalyst. Secure the bits

tightly using the 7mm wrench. To remove a tip, simply use the

7 mm wrench to unscrew the tip. Use the 8mm wrench to

hold the catalyst in place if required.

The wide flame head tip and the deflector tip can be slid over

the end of the catalyst. To remove them slide off the catalyst.

INSTALLING / REPLACING A NOZZLE

ALWAYS ALLOW THE TOOL TO COOL

FULLY BEFORE INSTALLING OR

REPLACING A NOZZLE.

The nozzle can get clogged, due to butane gas impurities. To

prolong the life of the tool, the nozzle is replaceable. Should

the nozzle be clogged, follow these steps to replace the nozzle:

1. Unscrew the flame guard nut.

2. Remove flame guard (and catalyst and tip if applicable).

3. Unscrew the ceramic insulator.

4. Remove the nozzle by hand (small copper part) by gently

turning and pulling it.

5. Install new nozzle with little opening facing outward.

6. Put the ceramic insulator back and securely tighten it.

7. Replace flame guard (and catalyst and tip if applicable).

8. Securely tighten flame guard nut.

The Dremel Versatip is now ready for use.

NOTE: A replacement nozzle can be ordered through your dealer.

MOST COMMON USE

Soldering tip: used for regular soldering activities, using

soldering tin.

Hot cutting knife: cutting of nylon rope to prevent 'feathering'.

Shaping knife: cutting to size of sheets of plastic and other

heat sensitive materials

Wide flame head: preparing for detailed paint removal

Hot air tip: melting of plastics and other heat-sensitive

materials

Deflector: shrinking of heat sensitive insulation around

electrical wiring

MAINTENANCE

CLEANING

Switch the tool off and allow to fully cool down before cleaning.

The exterior of the tool can be cleaned with a clean cloth. If

necessary use a damp cloth with a small amount of neutral

detergent. To clean the soldering tip, soak the soldering

sponge in some water. After soldering or in case of excess

solder on the tip, wipe it on the sponge when it is still hot.

SERVICE AND WARRANTY

This DREMEL product is guaranteed in accordance with

statutory/country specific regulations; damage due to normal

wear and tear, overload or improper handling will be excluded

from the guarantee. If the unit should fail despite the care

taken in manufacturing and testing, send it undismantled

together with proof of purchase to your dealer.

!

WARNING

!

WARNING

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Dremel 2000 Versatip Sculă electrică multifuncţională. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Dremel. S-ar putea să ofere un manual original. Căutați manualul dvs. Dremel 2000 Versatip Sculă electrică multifuncţională într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Dremel Scule electrice multifuncţionale
Mai multe manuale pentru Scule electrice multifuncţionale

Întrebări frecvente despre Dremel 2000 Versatip Sculă electrică multifuncţională

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

AEG OMN-IRT Sculă electrică multifuncţională

Manual

Pattfield PE-300MFW Sculă electrică multifuncţională

Manual

Skil 3650 CB Sculă electrică multifuncţională

Manual

Asist AE3C13N Sculă electrică multifuncţională

Manual

Pattfield PMF-300G Sculă electrică multifuncţională

Manual

Skil 3620 CA Sculă electrică multifuncţională

Manual

Ryobi RMT1801M Sculă electrică multifuncţională

Manual

Bosch PMF 2000 CE Sculă electrică multifuncţională

Categorii relevante