Manual Hendi 975398 Aparat de vidat

Manual

9

GB

Remark: Above table is just for reference only. In determining

the storage period, always suggesting the local sanitary-epi

-

demiological regulations and HACCP.

Cleaning & maintenance

• ATTENTION! Always disconnect the appliance from the elec-

trical mains and cool down before storage, cleaning & main-

tenance.

• Do not use water jet or steam cleaner for cleaning and do not

push the appliance under the water as the parts will get wet

and electric shock might be resulted.

• If the appliance is not kept in a good state of cleanliness, this

can adversely affect the life 0of the appliance and result in a

dangerous situation.

• Food residues should be regularly cleaned and removed from

the appliance. If the appliance is not cleaned properly, it will

reduce its lifespan and may result in a dangerous condition

during use.

Cleaning

• Clean the cooled exterior surface with a cloth or sponge

slightly dampened with a mild soap solution.

• For reasons of hygiene, the appliance should be cleaned be

-

fore and after use.

• Avoid water contacting the electrical components.

• Never use aggressive cleaning agents, abrasive sponges, or

cleaning agents containing chlorine. Do not use steel wool,

metallic utensils, or any sharp or pointed objects for cleaning.

Do not use petrol or solvents!

• Never immerse the appliance in water or other liquids.

Maintenance

• Check the operation of the appliance regularly to prevent se

-

rious accidents.

• If you see that the appliance is not working properly or that

there is a problem, stop using it, switch it off and contact the

supplier.

• All maintenance, installation and repair work must be car

-

ried out by specialised and authorised technicians, or recom-

mended by the manufacturer.

Transportation and Storage

• Before storage, always make sure that the appliance has

been disconnected from the power supply and completely

cooled down.

• Store the appliance in a cool, clean and dry place.

• Never place heavy objects on the appliance as this could

damage it.

• Do not move the appliance while it is under operation. Dis

-

connect the appliance from power supply when moving and

hold it at the bottom.

Troubleshooting

If the appliance does not function properly, please check the

below table for the solution. If you are still unable to solve the

problem, please contact the supplier/service provider.

Problems Possible solution

Appliance will

not turn on

•

Ensure that the machine is properly plugged

into a grounded outlet.

• Check the power cord for tears and frays. Do

not use machine if power cord is damaged.

• Make sure the Power button was properly

pressed. LED screen will be illuminated

when on.

Appliance does

not pull

a complete

vacuum with

pouch

• Vacuum/seal time may not be set high enough.

Set vacuum and seal times higher and vacuum

again.

• To vacuum and seal properly, the opening of

pouch must be within the vacuum chamber.

• If packaging from a roll pouch, make sure

first seal is complete and there are no gaps

in either seal.

• Vacuum packaging machine and vacuum

pouch need to be clean, dry and free of debris

for the vacuum process to be successful. Wipe

surface of seal bar and inside of pouch and

try again.

Vacuum pouch

loses vacuum

after being

sealed

• Sharp items can puncture small holes in

pouches. To prevent this, cover sharp edges

with paper towel and vacuum in a new pouch.

• Some fruits and vegetables can release gases

(out-gassing) if not properly blanched or

frozen before packaging. Open pouch. If you

think food spoilage has begun, discard food.

If food spoilage has not yet begun, consume

immediately. If in doubt, discard food.

Appliance is not

sealing pouch

properly

• Seal time may not be long enough. Increase

seal time and try again.

• Pouches will not seal if any moisture, food

particles or debris are present

in the seal area. Wipe the inside of the pouch

clean and try again.

• Pouch must be properly placed along the seal

bar. Make sure the entire pouch is over the

seal bar and there are no wrinkles in pouch

material.

Error code identification

Error

codes

Possible cause Possible solution

E01

When the

machine vacuum

for some time,

the two pressure

switches do not

close.

• Check if the vacuum lid is close;

• Check if the sealing gaskets are

assembled correctly;

• Check if the pump still works;

• Check if the pressure switches

are still good (check the con

-

necting pipe, pressure switches,

10P data cable, etc.)

E02

When the

machine enters

into Seal mode,

the micro-switch

does not close

.

• Check if the vacuum lid is close;

• Check if the micro-switch is

correct (GAS1 connecting wire,

micro-switch, 10P data cable,

etc.)

LP

The power is lost

suddenly during

the operation of

machine.

• Press “STOP” button to

release the air, then the LP will

disappear.

• If it appears again, please check

the power supply system (like

power cord, power socket, power

board).

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hendi 975398 Aparat de vidat. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hendi. S-ar putea să ofere un manual original. Căutați manualul dvs. Hendi 975398 Aparat de vidat într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Hendi Aparate de vidat
Mai multe manuale pentru Aparate de vidat

Produse asemanatoare

Manual

Hendi 970447 Aparat de vidat

Manual

Hendi 970362 Aparat de vidat

Manual

Hendi 975374 Aparat de vidat

Manual

Hendi 970430 Aparat de vidat

Manual

SilverCrest IAN 321553 Aparat de vidat

Manual

Switch On IAN 406272 Aparat de vidat

Manual

SilverCrest IAN 310996 Aparat de vidat

Manual

SilverCrest SFS 150 B3 Aparat de vidat

Categorii relevante