Manual Hikoki C 5MEY Ferăstrău circular

Ai nevoie de un manual pentru Hikoki C 5MEY Ferăstrău circular? Mai jos puteți vizualiza și descărca manualul PDF gratuit în limba română. Acest produs are în prezent 3 întrebări frecvente, 0 comentarii și are 0 voturi. Dacă acesta nu este manualul dorit, vă rugăm să ne contactați.

Produsul dvs. s-a defectat și manualul nu oferă nicio soluție? Mergeți la Repair Café pentru servicii de reparații gratuite.

Manual

Loading…

4
English
6. Do not stop the saw blades by lateral pressure on the
disc.
7. Always keep the saw blades sharp.
8. Ensure that the lower guard moves smoothly and freely.
9. Never use the circular saw with its lower guard xed in
the open position.
10. Ensure that the retraction mechanism of the guard
system operates correctly.
11. Wear earplugs to protect your ears during operation.
12. Never operate the circular saw with the saw blade turned
upward or to the side.
13. Ensure that the material is free of foreign matters such as
nails.
14. The saw blades shall be 125 mm.
15. Disconnect the plug from the receptacle before carrying
out any adjustment, servicing or maintenance.
16. Be careful of brake kickback.
This circular saw features an electric brake that functions
when the switch is released. As there is some kickback
when the brake functions, be sure to hold the main body
securely.
17. Ensure that the power source to be utilized conforms
to the power requirements speci ed on the product
nameplate.
18. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
19. When the work area is removed from the power source,
use an extension cord of su cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
20. Avoid cutting in the state where the base has oated up
from the material.
When blade is binding, or when interrupting a cut for any
reason, release the trigger and hold the saw motionless
in the material until the blade comes to a complete
stop. Never attempt to remove the saw from the work
or pull the saw backward while the blade is in motion or
KICKBACK may occur. Investigate and take corrective
actions to eliminate the cause of blade binding.
21. Support large panels to minimize the risk of blade
pinching and KICKBACK. Large panels tend to sag
under their own weight (Fig. 3). Supports must be
placed under the panel on both sides, near the line of cut
and near the edge of the panel as shown in Fig. 2.
To minimize the risk of blade pinching and kickback.
When cutting operation requires the resting of the saw
on the work piece, the saw shall be rested on the larger
portion and the smaller piece cut o .
22. Use extra caution when making a “Pocket Cut” into
existing walls or other blind areas. The protruding blade
may cut objects that can cause KICKBACK.
NEVER place your hand or ngers behind the saw
(Fig. 4). If kickback occurs, the saw could easily jump
backwards over your hand, possibly causing severe
injury.
23. WARNING: It is important to support the work piece
properly and to hold the saw rmly to prevent loss
of control which could cause personal injury. Fig. 5
illustrates typical hand support of the saw.
24. Place the wider portion of the saw base on that part
of the work piece which is solidly supported, not on
the section that will fall o when the cut is made. As
examples, Fig. 6 illustrates the RIGHT way to cut o the
end of board, and Fig. 7 the WRONG way. If the work
piece is short or small, clamp is down.
DON’T TRY TO HOLD SHORT PLACES BY HAND!
25. Never attempt to saw with the circular saw held upside
down in a vise. This is extremely dangerous and can
lead to serious accidents (Fig. 8).
26. When using the guide, do not attempt an inclined cut
which would allow the cut material to slip between the
saw blade and guide. Doing so could result in injury.
(Fig. 9)
27. Should lever remain loosened, it will create a very
hazardous situation. Always thoroughly clamp it.
(Fig. 13)
28. Prior to cutting operation, make sure the material you
are going to cut. If the material to be cut is expected to
generate harmful / toxic dusts, make sure the dust bag
or appropriate dust extraction system is connected with
dust outlet tightly.
Wear the dust mask additionally, if available.
Before starting to saw, con rm that the saw blade
has attained full-speed revolution.
Should the saw blade stop or make an abnormal
noise while operating, promptly turn OFF the switch.
Always take care in preventing the power cord from
coming near to the revolving saw blade.
Using the circular saw with the saw blade facing
upwards or sideways is very hazardous. Such
uncommon applications should be avoided.
When cutting materials, always wear protective
glasses.
When nished with a job, pull out the plug from the
receptacle.
29. After having attached the saw blade, recon rm that the
lock lever is rmly secured in the prescribed position.
30. Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your eye
will be hurt.
31. Check that there are no nicks or scratches in the cord.
32. Check the exterior and ensure that there is no damage.
33. Use a saw blade with a displayed rotational speed equal
to or higher than the rotational speed of the tool.
34. Use a saw blade that suits each di erent cutting material.
35. Always hold the tool rmly with one hand on handle.
(Fig. 27)
NAMES OF PARTS (Fig. 1 – Fig. 28)
1
Switch
2
Switch lock
3
Cutting depth lever
4
Cover
5
Link
6
Lower guard
7
Bolt
8
Washer (B)
9
Saw blade
0
Guide piece
!
Base
@
Incline lever
#
Lock lever
$
Guide fastener wing bolt
%
Link scale
^
LED light
&
Cord holder
*
Handle
(
Mode selector switch
)
Silent mode indicator lamp
0000Book̲C5MEY.indb40000Book̲C5MEY.indb4 2019/02/2716:32:272019/02/2716:32:27
Descărcaţi manualul în limba română (PDF, 15.16 MB)
(Protejați mediul înconjurător și imprimați acest manual numai dacă este neapărată nevoie)

Loading…

Evaluare

Spuneți-ne ce părere aveți despre Hikoki C 5MEY Ferăstrău circular, lăsând o evaluare a produsului. Doriți să împărtășiți experiența dvs. cu acest produs sau să adresați o întrebare? Lăsați un comentariu în partea de jos a paginii.
Ești mulțumit de Hikoki C 5MEY Ferăstrău circular?
Da Nu
Fiți primul care evaluează acest produs
0 voturi

Alăturați-vă conversației despre acest produs

Aici puteți împărtăși ce părere aveți despre Hikoki C 5MEY Ferăstrău circular. Dacă aveți o întrebare, citiți mai întâi cu atenție manualul. Solicitarea unui manual se poate face folosind formularul nostru de contact.

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hikoki C 5MEY Ferăstrău circular. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hikoki. S-ar putea să ofere un manual original. Căutați manualul dvs. Hikoki C 5MEY Ferăstrău circular într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Marcă Hikoki
Model C 5MEY
Categorie Fierastraie circular
Tip fișier PDF
Mărime fișier 15.16 MB

Toate manualele pentru Hikoki Fierastraie circular
Mai multe manuale pentru Fierastraie circular

Întrebări frecvente despre Hikoki C 5MEY Ferăstrău circular

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Câți milimetri trebuie să iasă ferăstrăul sub materialul pe care îl tăiem? Verificat

Cel mai bine este să păstrați acest lucru la 3 mm sau mai mult. Când este mai puțin, există șansa ca materialul să se prăbușească sau să ducă la un rezultat urât.

A fost util (95) Citeşte mai mult

Trebuie să port protecție auditivă atunci când folosesc un ferăstrău circular? Verificat

Da ar trebui. Deși cantitatea de zgomot produsă de un ferăstrău circular poate varia între mărci și modele, expunerea pe termen lung la zgomot puternic poate provoca leziuni permanente ale auzului. De aceea este o idee bună să purtați protecție auditivă.

A fost util (43) Citeşte mai mult

Pot depozita sculele electrice într-o magazie sau garaj? Verificat

În general, puteți depozita sculele electrice într-o magazie sau garaj, chiar dacă uneori îngheață acolo. Cu toate acestea, este mai bine pentru durata de viață a sculei electrice să o depozitați într-un loc uscat, fără fluctuații majore de temperatură. Într-o șopronă sau garaj, diferențele de temperatură pot provoca formarea de condens, care poate provoca rugina. În plus, uneltele care funcționează cu baterii durează mai puțin și nu se încarcă la fel de bine la temperaturi foarte scăzute. Pentru a fi sigur cum trebuie depozitată unealta electrică, citiți întotdeauna cu atenție manualul de utilizare.

A fost util (13) Citeşte mai mult
Manual Hikoki C 5MEY Ferăstrău circular

Produse asemanatoare

Categorii relevante