Manual Hikoki CS 30Y Ferăstrăul cu lanţ

Manual

8

English

STANDARD ACCESSORIES

○ Chain case .................................................................. 1

○ Guide bar ..................................................................... 1

○ Chain ........................................................................... 1

○ Plug clip*...................................................................... 1

* Not supplied in certain sales areas.

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES

(SOLD SEPARATELY)

○ Chain Saw Oil

○ Round File

○ Depth Gauge Jointer

Round File and Depth Gauge Jointer are to be used

for sharpening of chain blades. As to its application,

please refer to the item titled “Sharpening of the Chain

Blade”.

○ Chain Case

Always keep the chain cover on the chain while

carrying the chain saw or while storing it.

Optional accessories are subject to change without notice.

APPLICATIONS

General wood cutting.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specifi ed on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

3. Extension cord

When the work area is remote from the power source,

use an extension cord of suffi cient thickness and rated

capacity. The extension cord should be kept as short

as practicable.

4. Confi rm the chain tension

Improper chain tension may result in damage to the

chain and the guide bar, and could cause a serious

accident. Always confi rm that there is proper tension

on the chain prior to operation.

5. Fill the oil tank with oil

This unit is shipped without oil in the oil tank.

Prior to operation, remove the oil cap and fi ll the tank

with accessory oil.

This unit is shipped without oil in the oil tank.

Prior to operation, remove the oil cap and fi ll the tank

with chain saw oil (sold separately), or SAE 20 or 30

motor oil. Do not use stained or degraded motor oil.

Check oil reservoir periodically and keep it fi lled while

running saw.

6. It is recommended to use an earth-leakage circuit

breaker or a residual current device.

SAW CHAIN AND GUIDE BAR

ASSEMBLY

WARNING

○ Don’t use the saw chain or the guide bar other than

those specifi ed in “SPECIFICATIONS”.

○ Make sure the switch is turned off and the plug

disconnected from the socket.

○ Always wear gloves when handling the saw chain.

○ The tightening tension for the special nut has been

adjusted to the optimal level. Do not loosen it or tighten

it under any circumstances.

1. Removing the Saw Chain

(1) Check to make sure the chain brake has been released

before removing the side cover. (Fig. 3)

(2) Loosen the knob slightly and then loosen the tension

dial to release the tension on the saw chain. (Fig. 4)

(3) Completely loosen the knob and gently remove the

side cover.

(4) Gently remove the guide bar and saw chain.

2. Attaching the Saw Chain

(1) Set the guide bar on the attachment bolt.

(2) Loop the saw chain over the sprocket while taking care

over the direction it is facing, and then set the saw

chain in the guide bar groove. (Fig. 5)

(3) Set the clip on the side cover in the housing, put on

the side cover, rotate the tension dial, align the chain’s

tension pin with the hole on the guide bar and attach it

to the side cover. (Figs. 6 and 7)

CAUTION

If the knob is tightened before the tension dial is

rotated, the tension dial will be locked and it will not

rotate.

(4) Gently press the top of the knob to insert it into the

screw hole, tighten it and then follow the instructions in

“Adjusting the Chain Tension”.

CAUTION

○ When looping the saw chain over the sprocket, hold

the special nut in place to prevent the sprocket from

rotating. (Fig. 8)

○ If the special nut is accidently loosened or tightened,

cease use immediately and request repairs.

Using the chain saw as it is may prevent the chain

brake from operating normally and result in dangerous

situations.

ADJUSTING THE CHAIN TENSION

WARNING

○ Make sure switch is turned off and the plug

disconnected from the socket.

○ Always wear gloves when handling the saw chain.

○ The tightening tension for the special nut has been

adjusted to the optimal level. Do not loosen it or tighten

it under any circumstances.

(1) Raise the end of the guide bar and rotate the tension

dial to adjust the saw chain’s tension. (Fig. 9)

(2) Adjust the saw chain tension so that the gap between

the edge of the chain’s drive links and the guide bar is

between 0.5 mm and 1 mm when the chain is lightly

raised from the center of the guide bar. (Fig. 10)

(3) Once adjustment has been completed, raise the end of

the guide bar and fi rmly tighten the knob. (Fig. 9)

(4) Rotate the saw chain approximately one half of a

rotation while wearing gloves to reconfi rm that the

tension on the chain is correct.

CAUTION

If it is not possible to rotate the saw chain, check to

make sure that the chain brake has not been applied.

0000Book̲CS30Y.indb80000Book̲CS30Y.indb8 2017/12/0116:07:312017/12/0116:07:31

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hikoki CS 30Y Ferăstrăul cu lanţ. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hikoki. S-ar putea să ofere un manual original. Căutați manualul dvs. Hikoki CS 30Y Ferăstrăul cu lanţ într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Hikoki Ferăstraie cu lanţ
Mai multe manuale pentru Ferăstraie cu lanţ

Întrebări frecvente despre Hikoki CS 30Y Ferăstrăul cu lanţ

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Hikoki CS 30SB Ferăstrăul cu lanţ

Manual

Hikoki CS 3630DA Ferăstrăul cu lanţ

Manual

Hikoki CS 33EDP Ferăstrăul cu lanţ

Manual

Hikoki CS 33EB Ferăstrăul cu lanţ

Manual

Parkside IAN 497683 Ferăstrăul cu lanţ

Manual

Stihl GTA 26 Ferăstrăul cu lanţ

Manual

Yato YT-82836 Ferăstrăul cu lanţ

Manual

Yato YT-82837 Ferăstrăul cu lanţ

Categorii relevante