Manual Hikoki DH 28PEC Ciocan rotopercutor

Manual

4

English

Disconnect mains plug from electrical outlet

Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package

contains the accessories listed in the below.

○ Plastic case ................................................................ 1

○ Side handle ................................................................. 1

○ Depth gauge .............................................................. 1

Standard accessories are subject to change without notice.

APPLICATIONS

Rotation and hammering function

○ Drilling anchor holes

○ Drilling holes in concrete

○ Drilling holes in tile

Rotation only function

○ Drilling in steel or wood

(with optional accessories)

○ Tightening machine screws, wood screws

(with optional accessories)

Hammering only function

○ Light-duty chiselling of concrete, groove digging and

edging.

SPECIFICATIONS

The specifi cations of this machine are listed in the Table on

page 121.

NOTE

Due to HiKOKI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Inserting SDS-plus drilling tools 1 122

Removing SDS-plus drilling tools 2 122

Selecting rotation direction 3 122

Selecting the operating mode 4 122

Adjusting the drilling depth 5 122

Changing the chisel position 6 122

Selecting the operating mode 7 123

Auto stop function 8 123

Switching on and off and setting

the speed

9 123

Locking-on the On / Off switch 10 123

Releasing the On / Off switch 11 123

Selecting accessories* –

124

* For detailed information regarding each tool, contact a

HiKOKI authorized service center.

SELECT OPERATION MODE

Pressing the changeover switch allows the selection of

rotation speed and the auto stop function.

○ Rotation speed (Low mode/Normal mode)

Select either Low mode or Normal mode and operate the

tool in the selected speed.

○ Auto stop mode (on/off )

This product is equipped with an auto stop function to

support continuous drilling work. The function features a

memory mode for storing the work time for drilling from

switch ON to switch OFF, and an auto stop mode that

automatically stops the motor from the second drilling

onward should the work exceed the stored work time

while the switch is ON.

AUTO STOP FUNCTION

In selection mode, pressing the button for longer than two

seconds will move to memory mode.

(At the same time the auto stop lamp will blink.)

Conduct drilling when the auto stop lamp is fl ashing. The

time between switching ON and switching OFF is stored by

the tool.

(At the same time, the auto stop lamp will light up.)

Conduct drilling when the auto stop lamp is fl ashing.

Continuous drilling is possible as the memory storage time

will be recorded by the tool until the auto stop function’s auto

stop mode is cancelled.

The auto stop function is cancelled by pressing the

changeover switch once again for over two seconds.

(At the same time, the auto stop lamp will switch off .)

CAUTION

○ Switch ON the tool once you place the tip of the tool on

the work material.

○ The rotation speed and the level at which the switch is

pulled during drilling is not stored to memory.

○ Fully carry out drilling in one go during auto stop mode.

○ The motor will stop even if you switch OFF within the

memory storage time.

○ When you switch OFF within the memory storage time,

the count will be reset. If you rework a task in which a

hole has been partially drilled, the memory storage time

will be fully recounted.

REACTIVE FORCE CONTROL

This product is equipped with a Reactive Force Control

(RFC) feature that reduces jerking of the tool body.

If the tool bit is suddenly overburdened, any jerking of the

tool body is reduced by activation of the slip clutch or by

stopping of the motor by the sensor built into the tool body.

When the RFC is activated, the two LEDs fl ash red in

a synchronized manner. (Table 1) During the fl ashing,

the motor will be off . Press the changeover switch to

recommence operation.

Because the RFC feature may not activate or its performance

may be insuffi cient depending on the working environment

and conditions, be careful not to suddenly overburden the

tool bit while operating.

● Possible causes of sudden overburdening

1 Tool bit biting into material

2 Impact against nails, metal or other hard objects

3 Tasks involving prying or any excess application of

pressure, etc.

Also, other causes include any combination of the

aforementioned.

0000Book̲DH28PEC.indb40000Book̲DH28PEC.indb4 2019/01/2311:53:412019/01/2311:53:41

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hikoki DH 28PEC Ciocan rotopercutor. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hikoki. S-ar putea să ofere un manual original. Căutați manualul dvs. Hikoki DH 28PEC Ciocan rotopercutor într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Hikoki Ciocane rotopercutoare
Mai multe manuale pentru Ciocane rotopercutoare

Întrebări frecvente despre Hikoki DH 28PEC Ciocan rotopercutor

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Hikoki DH 24PG Ciocan rotopercutor

Manual

Hikoki DH 25DL Ciocan rotopercutor

Manual

Hikoki DH 36DPA Ciocan rotopercutor

Manual

Hikoki DH 24PG2 Ciocan rotopercutor

Manual

AEG KH 28 Super XE Ciocan rotopercutor

Manual

Einhell TP-HD 18/26 D Li BL Ciocan rotopercutor

Manual

Bort BHD-900 Ciocan rotopercutor

Manual

Skil 1034 AE Ciocan rotopercutor

Categorii relevante