Manual Hikoki DV 18DGAL Maşină de găurit-înşurubat

Manual

3

English

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a fi re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, fl ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

6) Service

a) Have your power tool serviced by a qualifi ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and infi rm persons away.

When not in use, tools should be stored out of reach of

children and infi rm persons.

CORDLESS COMBI DRILL SAFETY

WARNINGS

1. Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

2. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory or fastener may contact hidden wiring.

Cutting accessory and fasteners contacting a "live" wire

may make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

ADDITIONAL SAFETY WARNINGS

1. Make sure that the area to be drilled is absolutely free

of any hidden obstructions including electrical wiring,

water, or gas pipes. Drilling into the aforementioned may

result in electric shock or short circuit, gas leak or other

hazards that can cause serious accidents or injuries.

2. Make sure to securely hold the tool during operation.

Failure to do so can result in accidents or injuries.

3. Secure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than

by hand.

4.

Setting up and checking the work environment. Check if the

work environment is suitable by following the precaution.

5. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

6. Never disassemble the rechargeable battery and charger.

7. Never short-circuit the rechargeable battery.

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

8. Do not dispose of the battery in fi re. If the battery is burnt,

it may explode.

9. Bring the battery to the shop from which it was purchased

as soon as the post-charging battery life becomes too

short for practical use. Do not dispose of the exhausted

battery.

10. Do not insert object into the air ventilation slots of the

charger. Inserting metal objects or infl ammables into the

charger air ventilation slots will result in electrical shock

hazard or damaged charger.

11. When mounting a bit into the keyless chuck, tighten the

sleeve adequately. If the sleeve is not tight, the bit may

slip or fall out, causing injury.

12. When changing the rotational speed with the shift knob,

confi rm that the switch is off . Changing the speed while

the motor is rotating will damage the gears.

13. The clutch dial cannot be set between the numerals "1,

3, 5 … 22" or the dots, and do not use with the clutch dial

numeral between "22" and the line at the middle of the

drill mark. Doing so may cause damage.

14. Always use this unit with clockwise rotation, when using

it as an impact drill.

15. Resting the unit after continuous work.

16. The motor may stop in the event the tool is overloaded. In

this should occur, release the tool’s switch and eliminate

the cause of the overload.

17. The motor rotation may be locked to cease while the unit

is used as drill. While operating the driver drill, take care

not to lock the motor.

18. If motor is locked, immediately turn the power off . If the

motor is locked for a while, the motor or battery may be

burnt.

19. The use of the battery in a cold condition (below 0 degree

Centigrade) can sometimes result in the weakened

tightening torque and reduced amount of work. This,

however, is a temporary phenomenon, and returns to

normal when the battery warms up.

20. Do not look directly into the light. Such actions could

result in eye injury.

21. Stow the bit in the specifi ed location on the tool. If the

tool is used with the bit stowed improperly, the bit may

fall and cause bodily injury.

22. Do not stow bits that are of a diff erent length, gauge or

dimension than the plus driver bit (65 mm long) included

in the STANDARD ACCESSORIES.

The bit may fall and cause bodily injury.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may stop.

This is not the trouble but the result of protection function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand, please

be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall on

the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust that

may adhere to it and do not store it together with metal

parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject the

battery to severe physical shock.

3. Do not use an apparently damaged or deformed battery.

4. Do not use the battery in reverse polarity.

0000BookDV18DGAL.indb30000BookDV18DGAL.indb3 2019/07/2318:10:162019/07/2318:10:16

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hikoki DV 18DGAL Maşină de găurit-înşurubat. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hikoki. S-ar putea să ofere un manual original. Căutați manualul dvs. Hikoki DV 18DGAL Maşină de găurit-înşurubat într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Hikoki Maşini de găurit-înşurubat
Mai multe manuale pentru Maşini de găurit-înşurubat

Întrebări frecvente despre Hikoki DV 18DGAL Maşină de găurit-înşurubat

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Hikoki DV 18DD Maşină de găurit-înşurubat

Manual

Hikoki DS 14DSDL Maşină de găurit-înşurubat

Manual

Hikoki DS 9DVF3 Maşină de găurit-înşurubat

Manual

Hikoki DS 14DL2 Maşină de găurit-înşurubat

Manual

Hikoki DS 14DCL Maşină de găurit-înşurubat

Manual

Hikoki DS 10DAL Maşină de găurit-înşurubat

Manual

Hikoki DS 18DD Maşină de găurit-înşurubat

Manual

Skil 3303 EA Maşină de găurit-înşurubat

Categorii relevante