Manual Hikoki DV 18DGAL Maşină de găurit-înşurubat

Manual

6

English

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger fi rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used, the

pilot lamp of the charger lights for 1 second, does not

light for 0.5 seconds (off for 0.5 seconds). In such a case,

fi rst let the battery cool, then start charging.

○ When the pilot lamp fl ickers (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s

battery connector. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

○

Since the built-in micro computer takes about 3 seconds to

confi rm that the battery being charged with charger is taken

out, wait for a minimum of 3 seconds before reinserting

it to continue charging. If the battery is reinserted within

3

seconds, the battery may not be properly charged.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery 1 162

Charging 2 162

Tightening torque adjustment 3 162

Selecting the drill position 4 162

Selecting the impact position 5 162

Change rotation speed 6 162

How to use the LED light 7 163

Mounting the bit 8 163

Reversing the rotational direction 9 163

Switch operation 10 163

Using the bit holder 11 163

Selecting accessories ― 164

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade effi ciency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the driver drill is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

Store the power tool in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signifi cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signifi cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to fi ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modifi ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specifi c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 93 dB (A)

Measured A-weighted sound pressure level: 82 dB (A)

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Impact drilling into concrete:

Vibration emission value a

h

, ID =

12.1 m/s

2

Uncertainty K = 1.5 m/s

2

0000BookDV18DGAL.indb60000BookDV18DGAL.indb6 2019/07/2318:10:162019/07/2318:10:16

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hikoki DV 18DGAL Maşină de găurit-înşurubat. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hikoki. S-ar putea să ofere un manual original. Căutați manualul dvs. Hikoki DV 18DGAL Maşină de găurit-înşurubat într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Hikoki Maşini de găurit-înşurubat
Mai multe manuale pentru Maşini de găurit-înşurubat

Întrebări frecvente despre Hikoki DV 18DGAL Maşină de găurit-înşurubat

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Hikoki DV 18DD Maşină de găurit-înşurubat

Manual

Hikoki DS 14DSDL Maşină de găurit-înşurubat

Manual

Hikoki DS 9DVF3 Maşină de găurit-înşurubat

Manual

Hikoki DS 14DL2 Maşină de găurit-înşurubat

Manual

Hikoki DS 14DCL Maşină de găurit-înşurubat

Manual

Hikoki DS 10DAL Maşină de găurit-înşurubat

Manual

Hikoki DS 18DD Maşină de găurit-înşurubat

Manual

Skil 3303 EA Maşină de găurit-înşurubat

Categorii relevante