Manual Hikoki DV 20VD Maşină de găurit cu percuţie

Manual

4

English

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package

contains the accessories listed in the below.

(1) Chuck wrench (Spec. only for keyed chuck) ................1

(2) Side handle ..................................................................1

(3) Depth gauge ................................................................1

(4) Plastic case ..................................................................1

Standard accessories are subject to change without notice.

APPLICATIONS

○ By combined actions of ROTATION and IMPACT:

Boring holes in hard materials (concrete, marble, granite,

tiles, etc.)

○ By ROTATIONAL action:

Boring holes in metal, wood and plastic.

SPECIFICATIONS

Voltage*

1

(110 V, 220 V, 230 V, 240 V)

Power input 860 W*

1

Speed range 1 2

No load speed 0 – 1100 min

-1

0 – 3000 min

-1

Capacity

Steel

13 mm 8 mm

Concrete

20 mm 13 mm

Wood

40 mm 25 mm

Full-load impact rate

8100 min

-1

22000 min

-1

Weight*

2

3.0 kg

*1 Be sure to check the nameplate on product as it is subject

to change by areas.

*2 Weight: According to EPTA-Procedure 01/2003

NOTE

Due to HiKOKI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Insulated gripping surface 1 99

Fixing and removing side handle

299

Using depth stopper 3 99

Mounting and dismounting of

the bit

499

Selecting rotation direction 5 100

Selecting the operating mode 6 100

Switch operation

7 100

Locking-on the switch

8 100

Releasing the switch

9 100

Change rotation speed

10 101

Selecting accessories ― 102

Selecting the appropriate drill bit

○ When boring concrete or stone

Use the drill bits specifi ed in the Optional Accessories.

○ When boring metal or plastic

Use an ordinary metalworking drill bit.

○ When boring wood

Use ordinary woodworking drill bit.

However, when drilling 6.5 mm or smaller holes, use a

metalworking drill bit.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits

Since use of an abraded drill bits will cause motor

malfunctioning and degraded effi ciency, replace the drill

bits with a new one or resharpening without delay when

abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection,

carbon brush inspection and replacement on this tool

should ONLY be performed by a HiKOKI Authorized

Service Center.

5. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HiKOKI Authorized Service Center to

avoid a safety hazard.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specifi c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

0000Book̲DV20VD.indb40000Book̲DV20VD.indb4 2017/12/0411:00:552017/12/0411:00:55

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hikoki DV 20VD Maşină de găurit cu percuţie. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hikoki. S-ar putea să ofere un manual original. Căutați manualul dvs. Hikoki DV 20VD Maşină de găurit cu percuţie într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Hikoki Maşini de găurit cu percuţie
Mai multe manuale pentru Maşini de găurit cu percuţie

Întrebări frecvente despre Hikoki DV 20VD Maşină de găurit cu percuţie

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Hikoki DV 13SS Maşină de găurit cu percuţie

Manual

Hikoki D 13VL Maşină de găurit cu percuţie

Manual

Hikoki D 13VB3 Maşină de găurit cu percuţie

Manual

Hikoki DV 22V Maşină de găurit cu percuţie

Manual

Hikoki DV 16V Maşină de găurit cu percuţie

Manual

Hikoki D 10VST(L) Maşină de găurit cu percuţie

Manual

Hikoki DV 20VB2 Maşină de găurit cu percuţie

Manual

Asist AE1P75N Maşină de găurit cu percuţie

Categorii relevante