Manual Hoover HGL64SCF C Plită

Manual

05 GB - IE

1. INSTRUCTIONS FOR THE INSTALLER

The hob may be installed in any worktop which is heat resistant to a

temperature of 100°C, and has a thickness of 25-45 mm. The

dimensions of the insert to be cut out of the worktop are in shown in

Figure 2.

If the Hob is fitted next to a cabinet on either side, the distance between

the Hob and the cabinet must be at least 15 cm (see Figure 4); while the

distance between the hob and the rear wall must be at least 5,5 cm.

The distance between the hob and any other unit or appliance above it

(e.g. An extractor hood) must be no less than 70 cm (Figure 4).

When there is an accessible space between the built-in hob and the

cavity below, a dividing wall made of insulating material should be

inserted (wood or a similar material) (Figure 3).

Important - The diagram in figure 1 shows how the sealant should

be applied.

The Hob unit is fitted by attaching the Fixing Clamps supplied, using the

holes at the base of the unit.

If a hob of 60 cm is fitted above an oven which is not equipped with fan

cooling system it is recommended that openings are created within the

built in furniture to ensure correct air circulation.

The size of these openings must be at least 300 cm2 and placed as

shown in Figure 5.

2. ELECTRICAL CONNECTION (FOR U.K. ONLY)

Warning - this appliance must be earthed

This appliance is designed for domestic use only. Connection to the

main supply must be made by a competant electrician, ensuring that

all current regulations concerning such installations are observed.

The appliance must only be connected to a suitably rated spur point, a

3 pin 13 amp plug/socket is not suitable. A double pole switch must be

provided and the circuit must have appropriate fuse protection.

Further details of the power requirement of the individual product will

be found in the users’ instruction and on the appliance rating plate. In

the case of built-in product you are advised, should you wish to use a

longer cable than the one supplied, that a suitably rated heat resistant

type must be used.

The wiring must be connected to the mains supply as follows:

CONNECT TO SPUR TERMINAL

Green & Yellow Wire Earth Connection

Blue Wire Neutral Connection

Brown Wire Live Connection

Note: We do not advocate the use of earth leakage devices with

electric cooking appliances installed to spur points because of the

«nuisance tripping» which may occur. You are again reminded that the

appliance must be correctly earthed, the manufacturer declines any

responsibility for any event occurring as a result of incorrect electrical

installation.

INSTALLING A DOMESTIC APPLIANCE CAN BE A COMPLICATED OPERATION WHICH IF NOT CARRIED OUT CORRECTLY, CAN SERIOUSLY

AFFECT CONSUMER SAFETY. IT IS FOR THIS REASON THAT THE TASK SHOULD BE UNDERTAKEN BY A PROFESSIONALLY QUALIFIED

PERSON WHO WILL CARRY IT OUT IN ACCORDANCE WITH THE TECHNICAL REGULATIONS IN FORCE. IN THE EVENT THAT THIS ADVICE IS

IGNORED AND THE INSTALLATION IS CARRIED OUT BY AN UNQUALIFIED PERSON, THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR ANY TECHNICAL FAILURE OF THE PRODUCT WHETHER OR NOT IT RESULTS IN DAMAGE TO GOODS OR INJURY TO INDIVIDUALS.

1.1 BUILDING IN

1.2. SUITABLE LOCATION

This appliance must be installed in accordance with applicable

regulations and should only be used in well-ventilated locations.

Before using this appliance carefully study the instruction book.

2.1. ELECTRICAL CONNECTION

Check the data on the rating plate, located on the outside of the unit, to

ensure that the supply and input voltage are suitable.

Before connection, check the earthing system.

By Law, this appliance must be earthed. If this regulation is not

complied with, the Manufacturer will not be responsible for any

damage caused to persons or property. If a plug is not already

attached, fit a plug appropriate to the load indicated on the rating plate.

The earth wire is coloured yellow/green. The plug should always be

accessible.

Where the Hob is connected direct to the electricity supply, a circuit

breaker must be fitted.

LIVE

EARTH

NEUTRAL

L

N

Power Cable

Brown Wire

Green/Yellow Wire

Blue Wire

Mains Supply

2.2. GAS CONNECTION

These instructions are for qualified personnel, installation of

equipment must be in line with the relevant national standard. (For

U.K. only: by law the gas installation\commissioning must be

carried out by a "Gas Safe" installer)

All work must be carried out with the electricity supply disconnected.

The rating plate on the hob shows the type of gas with which it is

designed to be used. Connection to the mains gas supply or gas

cylinder should be carried out after having checked that it is regulated

for the type of gas with which it will be supplied. If it is not correctly

regulated see the instructions in the following paragraphs to change

gas setting

For liquid gas (cylinder gas) use pressure regulators which comply

with the relevant national standards.

Use only pipes,washers and sealing washers which comply with the

relevant national standards.

To prevent any potential damage to the hob please carry out the

installation following this sequence (picture 6):

For some models a conic link is furnished to outfit for the installation in

the countries where this type of link is obligatory; in picture 8 it is

pointed out how to recognize the different types of links (CY =

cylindrical, CO = conic). In every case the cylindrical part of the link

has to be connected to the hob.

When connecting the hob to the gas supply via use offlexible hoses

please ensure that the maximum distance covered by the hose does

not exceed 2 metres.

If the power supply cord is damaged this is to be replaced by a

qualified engineer so as to prevent any potential risk.

The earth wire ( green and yellow coloured ) must be at least 10 mm

longer than the live and neutral wires.

The section of the cable used must be of the correct size in relation to

the absorbed power of the hob.

Please check rating plate for the power details and ensure that the

power supply cord is of the type H05RR-F, H05VV-F, H05V2V2-F.

1)As illustrated, assemble parts in sequence:

A: 1/2 Male Adaptor Cylindirical

B: 1/2 Seal

C: 1/2 Female Gas Adaptor Conical-Cylindirical or

Cylindirical-Cylindirical

2)Tighten the joints with the spanner, remembering to twist the

pipes into position.

3)Attach fitting C to mains gas supply using rigid copper pipe or

flexible steel pipe.

IMPORTANT: carry out a final check for leaks on the pipe

connections using a soapy solution. NEVER USE A FLAME. Also,

make sure that the flexible pipe cannot come into contact with a

moving part of the cabinet (eg.adrawer) and that it is not situated

where it could be damaged.

Warning: If gas can be smelt in the vicinity of this appliance turn off the gas

supply to the appliance and call the engineer directly. Do not search for a

leak with a naked flame.

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hoover HGL64SCF C Plită. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hoover. S-ar putea să ofere un manual original. Căutați manualul dvs. Hoover HGL64SCF C Plită într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Hoover Plite
Mai multe manuale pentru Plite

Întrebări frecvente despre Hoover HGL64SCF C Plită

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Hoover HGV64SMTCG W Plită

Manual

Hoover HHG6BR4WSX Plită

Manual

Hoover HGVL6040B Plită

Manual

Hoover HHG75WMX Plită

Manual

Hoover HHW6BRBX Plită

Manual

Hoover HVW6MW Plită

Manual

Hoover HGV64SCB Plită

Manual

Hoover HHG7MX Plită

Categorii relevante