Manual Maestro MR658 Aparat de tuns

Manual

8 9

downward gradually increases the cutting length. See Picture 3

(page 2).

-In its lowest position, the lever will leave the hair approximately the

same length as the #1 comb.

-The lever will also extend the use of your blades since a different

cutting edge is used in each setting. In addition, if extremely heavy

hair cutting has jammed the blades, it will help you remove hair that

has become wedged between the two blades without removing the

blades.

-While the clipper is running, rapidly move the lever from “close

cut” to “longer cut“ a couple of times. Doing this each time after you

have nished using your clipper will help to keep the blades clear. If

your clipper stops cutting and this does not help, your cutting blades

are dulled. Replace them with new blades.

Preparation for use

- Remove all wrap materials and stickers

- Make sure that all the parts of appliance don’t have damages.

- Inspect the clipper, making sure that it is free of oil between the

cutting blade teeth and turn the unit on to distribute the oil and to

make sure it is running smoothly. Wipe off any excess oil. This

should be done before each use.

-While using the unit, untwist the cord from time to time to avoid

tangling.

- Seat the person so their head is approximately at your eye level.

This allow ease of visibility while cutting and a relaxed control of the

unit

- Before cutting always rst comb the hair so it is tangle free and as

it is naturally worn.

Reminders

- Cut the hair in a relaxed and slow manner. Use short strokes only

to work gradually over the entire head.

- Always take off a little hair at a time; you can always trim off

additional hair later.

- As you work, comb the hair frequently back into the style to which

you are cutting.

- When cutting with this hair clipper it is better to leave the hair dry,

not wet. With the hair dry, it is much easier to control the amount of

hair being cut.

Attachment Combs (see main diagram).

Each comb attachment is marked accordingly on its outside middle

surface.

- To attach a comb, hold it with its teeth, upward and slide it along

the clipper blade until the front of the comb rmly seats against the

clipper blade.

- To remove the comb, simple pull the comb upward and away from

the clipper blade.

For even cutting, allow the comb attachment/cutter to cut its way

through the hair. Do not force it through quickly. Also remember to

comb the hair frequently to remove trimmed hair and to check for

uneven strands.

EN

Attachment Comb leaves hair length mm (inch)

№1 3(1/8)

№2 6(1/4)

№3 9(3/8)

№4 12(1/2)

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Maestro MR658 Aparat de tuns. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Maestro. S-ar putea să ofere un manual original. Căutați manualul dvs. Maestro MR658 Aparat de tuns într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Maestro Aparate de tuns
Mai multe manuale pentru Aparate de tuns

Întrebări frecvente despre Maestro MR658 Aparat de tuns

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Maestro MR650C Aparat de tuns

Manual

Maestro MR-662 Aparat de tuns

Manual

Maestro MR651 Aparat de tuns

Manual

Maestro MR655 Aparat de tuns

Manual

Maestro MR651C Aparat de tuns

Manual

Maestro MR653C Aparat de tuns

Manual

Maestro MR656 Aparat de tuns

Manual

Maestro MR654C Aparat de tuns

Categorii relevante