Manual Makita DDF444 Maşină de găurit-înşurubat

Manual

7

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

Lighting up the front lamp

Fig.4

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to light up the lamp. The lamp keeps

on lighting while the switch trigger is being pulled. The

lamp goes out 10 -15 seconds after releasing the trigger.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp.

Be careful not to scratch the lens of lamp, or it may

lower the illumination.

Reversing switch action

Fig.5

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before

operation.

• Use the reversing switch only after the tool comes

to a complete stop. Changing the direction of

rotation before the tool stops may damage the tool.

• When not operating the tool, always set the

reversing switch lever to the neutral position.

Speed change

Fig.6

To change the speed, first switch off the tool and then

slide the speed change lever to the "2" side for high

speed or, "1" side for low speed. Be sure that the speed

change lever is set to the correct position before

operation. Use the right speed for your job.

CAUTION:

•

Always set the speed change lever fully to the

correct position. If you operate the tool with the

speed change lever positioned halfway between the

"1" side and , "2" side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

Selecting action mode

Fig.7

This tool has an action mode change lever. For drilling,

slide the action mode change lever to the left (

symbol).

For screwing, slide the action mode change lever to the

right (

symbol).

NOTE:

• When changing the position from " " to " ", it

may be a little difficult to slide the mode change

lever. At this time, switch on and run the tool for a

second at the "

" position, then stop the tool and

slide to your desired position.

CAUTION:

• Always slide the action mode change lever all the

way to your desired mode position. If you operate

the tool with the lever positioned halfway between

the mode symbols, the tool may be damaged.

• Do not use the action mode change lever while the

tool is running. The tool may be damaged.

Adjusting the fastening torque

Fig.8

The fastening torque can be adjusted in 16 steps by

turning the adjusting ring so that its graduations are

aligned with the pointer on the tool body.

First, slide the action mode change lever to the position

of

symbol.

The fastening torque is minimum when the number 1 is

aligned with the pointer, and maximum when the marking

is aligned with the pointer. The clutch will slip at various

torque levels when set at the number 1 to 16. Before

actual operation, drive a trial screw into your material or a

piece of duplicate material to determine which torque

level is required for a particular application.

NOTE:

• The adjusting ring does not lock when the pointer is

positioned only halfway between the graduations.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out

any work on the tool.

Installing side grip (auxiliary handle)

Fig.9

Always use the side grip to ensure operating safety.

Insert the side grip so that the protrusions on the grip

base and steel band fit in between the grooves on the

tool barrel. Then tighten the grip by turning clockwise.

Installing or removing driver bit or drill bit

Fig.10

Turn the sleeve counterclockwise to open the chuck jaws.

Place the bit in the chuck as far as it will go. Turn the

sleeve clockwise to tighten the chuck. To remove the bit,

turn the sleeve counterclockwise.

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Makita DDF444 Maşină de găurit-înşurubat. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Makita. S-ar putea să ofere un manual original. Căutați manualul dvs. Makita DDF444 Maşină de găurit-înşurubat într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Makita Maşini de găurit-înşurubat
Mai multe manuale pentru Maşini de găurit-înşurubat

Întrebări frecvente despre Makita DDF444 Maşină de găurit-înşurubat

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Makita DF457DWE Maşină de găurit-înşurubat

Manual

Makita DDF454 Maşină de găurit-înşurubat

Manual

Makita DF347DWE Maşină de găurit-înşurubat

Manual

Skil 3076 JA Maşină de găurit-înşurubat

Manual

Sthor 78981 Maşină de găurit-înşurubat

Manual

Skil 3020 HC Maşină de găurit-înşurubat

Manual

Skil 3071 EA Maşină de găurit-înşurubat

Manual

Flex DD 2G 10.8-LD Maşină de găurit-înşurubat

Categorii relevante