Manual Ryobi R18MS216-0 Fierastrau circular stationar

Manual

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power tool accidentally.

■ Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

■ Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

■ Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

■ Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

■ Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

■ Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another battery pack.

■ Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury and fire.

■ When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause

burns or a fire.

■ Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

■ Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or

risk of injury.

■ Do not expose a battery pack or tool to fire

or excessive temperature. Exposure to fire or

temperature above 130’C may cause explosion.

■ Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified

range may damage the battery and increase the risk

of fire.

SERVICE

■ Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

■ Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SAFETY INSTRUCTIONS FOR MITRE SAWS

■ Mitre saws are intended to cut wood or wood-like

products, they cannot be used with abrasive cut-

off wheels for cutting ferrous material such as bars,

rods, studs, etc. Abrasive dust causes moving parts

such as the lower guard to jam. Sparks from abrasive

cutting will burn the lower guard, the kerf insert and

other plastic parts.

■ Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to

the saw blade, there is an increased risk of injury from

blade contact.

■ The workpiece must be stationary and clamped or

held against both the fence and the table. Do not

feed the workpiece into the blade or cut “freehand”

in any way. Unrestrained or moving workpieces could

be thrown at high speeds, causing injury.

■ Push the saw through the workpiece. Do not pull the

saw through the workpiece. To make a cut, raise the

saw head and pull it out over the workpiece without

cutting, start the motor, press the saw head down

and push the saw through the workpiece. Cutting on

the pull stroke is likely to cause the saw blade to climb

on top of the workpiece and violently throw the blade

assembly towards the operator.

■ Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e. holding

the workpiece to the right of the saw blade with your left

hand or vice versa is very dangerous.

■ Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity

of the spinning saw blade to your hand may not be

obvious and you may be seriously injured.

■ Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece,

fence and table along the line of the cut. Bent or

warped workpieces can twist or shift and may cause

binding on the spinning saw blade while cutting. There

should be no nails or foreign objects in the workpiece.

■ Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the workpiece.

Small debris or loose pieces of wood or other objects

that contact the revolving blade can be thrown with high

speed.

2

Original Instructions

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Ryobi R18MS216-0 Fierastrau circular stationar. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Ryobi. S-ar putea să ofere un manual original. Căutați manualul dvs. Ryobi R18MS216-0 Fierastrau circular stationar într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Ryobi Fierastraie circulare stationare
Mai multe manuale pentru Fierastraie circulare stationare

Întrebări frecvente despre Ryobi R18MS216-0 Fierastrau circular stationar

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Ryobi ETMS1825 Fierastrau circular stationar

Manual

Ryobi EMS190DC Fierastrau circular stationar

Manual

Ryobi RMS18254X-0 Fierastrau circular stationar

Manual

Ryobi RMS18190-0 Fierastrau circular stationar

Manual

Bosch GTM 12 JL Fierastrau circular stationar

Manual

Bosch GCM 350-254 Professional Fierastrau circular stationar

Manual

Parkside IAN 304475 Fierastrau circular stationar

Manual

Metabo KGSV 216 M Fierastrau circular stationar

Categorii relevante