Manual Ryobi RLM1956MEB Mașină de tuns iarbă

Manual

English

6

2. Remove the hub cap.

3. Remove the nut from the wheel axle, then remove the

wheel.

4. Replace with new wheel and reinstall nut to secure.

CLEANING THE AIR FILTER

See fi gure 8.

For proper performance and long life, keep the air fi lter

clean.

1. Remove the air fi lter cover by pushing down the latch

while gently pulling out the cover.

2. Remove the air fi lter and clean it in warm soapy water.

Rinse and let dry completely.

3. Apply a light coat of engine oil to the air fi lter, then

squeeze it out using an absorbent cloth or paper towel.

4. Reinstall the air fi lter into the air fi lter base.

5. Replace and secure the air fi lter cover.

NOTE: The filter should be replaced annually for best

performance.

WARNING

A leaking fuel cap is a fi re hazard and must be replaced

immediately.

The fuel cap contains a non-serviceable fi lter and a

check valve. A clogged fuel cap will cause poor engine

performance. If performance improves when the fuel

cap is loosened, check valve may be faulty or clogged.

Replace fuel cap if required.

CHANGING THE ENGINE OIL

See fi gure 8.

Engine oil should be changed after every 25 hours of use.

Change the oil while the engine oil is still warm, but not hot.

This allows the oil to drain quickly and completely.

1. Remove the oil fi ll cap/dipstick.

2. Tip mower onto its side and allow oil to drain from the oil

fi ll hole into an approved container.

3. Place mower upright and refi ll with oil.

NOTE: Used oil should be disposed of at an approved

disposal site. See your local oil retailer for more

information.

MAINTAINING THE SPARK PLUG

See fi gure 7.

The spark plug must be properly gapped and free of

deposits in order to ensure proper engine operation. To

check:

1. Remove spark plug boot.

2. Clean any dirt from around base of spark plug.

3. Remove spark plug using a 13/16 in. spark plug socket

(not provided).

4. Inspect spark plug for damage, and clean with a wire

brush before reinstalling. If insulator is cracked or

chipped, spark plug should be replaced.

NOTE: If replacing, use the following recommended

plugs are Torch E7RTC is NGK BPR6HS.

5. Measure plug gap. The correct gap is 0.028 − 0.031 in.

To widen gap, if necessary, carefully bend the ground

(top) electrode. To lessen gap, gently tap ground

electrode on a hard surface.

6. Seat spark plug in position; thread in by hand to prevent

cross-threading.

7. Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

8. Reinstall spark plug boot.

STORING THE PRODUCT

When storing the mower for 30 days or more:

■ If using fuel stabilizer, follow stabilizer manufacturer’s

directions to add stabilizer to petrol in fuel tank. Run

engine at least 10 minutes after adding stabilizer to

allow the stabilizer to reach the carburetor.

WARNING

Do not store the lawn mower with petrol in the tank

inside a building where fumes may reach an open fl ame

or spark.

■ If not using fuel stabilizer, allow the engine to run until

the mower is completely out of petrol.

■ Once the engine has stopped, allow the blade to come

to a complete stop and disconnect the spark plug wire.

■ Turn the fuel valve to the closed position.

■ Turn mower on its side (with carburetor facing up) and

clean grass clippings that have accumulated on the

underside of the mower deck.

■ Clean the underside of the mower deck.

■ Wipe the mower clean with a dry cloth.

■ Check all nuts, bolts, knobs, screws, fasteners, etc., for

tightness.

■ Inspect moving parts for damage, breakage, and wear.

Have repairs made on any damaged or missing parts.

■ Store the mower in a well-ventilated area that is clean,

dry, and out of the reach of children.

■ Do not store near corrosive materials such as fertilizer

or rock salt.

To lower the handle before storing:

■ Loosen the starter rope guide knob. Remove starter

rope from guide and allow to retract into engine.

■ Fully loosen the handle knobs on the sides of the

handle and fold the upper handle down.

■ Unscrew the lower handle lock nuts.

■ Fold the lower handle forward, making sure not to bend

or kink the control cables.

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Ryobi RLM1956MEB Mașină de tuns iarbă. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Ryobi. S-ar putea să ofere un manual original. Căutați manualul dvs. Ryobi RLM1956MEB Mașină de tuns iarbă într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Ryobi Maşini de tuns iarbă
Mai multe manuale pentru Maşini de tuns iarbă

Întrebări frecvente despre Ryobi RLM1956MEB Mașină de tuns iarbă

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Ryobi RLM36X46L5F Mașină de tuns iarbă

Manual

Ryobi RY18LMX40A Mașină de tuns iarbă

Manual

Ryobi OLM1841H Mașină de tuns iarbă

Manual

Ryobi RLM18X33B40 Mașină de tuns iarbă

Manual

Ryobi OLM1836H Mașină de tuns iarbă

Manual

Ryobi RY36LMMX51A Mașină de tuns iarbă

Manual

Ryobi RY36LMXSP46A Mașină de tuns iarbă

Manual

Ryobi RLM18X41H240 Mașină de tuns iarbă

Categorii relevante