Manual Ryobi RMS18254X-0 Fierastrau circular stationar

Manual

■ Never reach into the area near the blade unless the

blade has completely stopped.

■ Before use, thoroughly check the product and battery

pack for any damage or material fatigue. Repairs to

the whole product should only be carried out by an

authorised service centre.

■ Always use the guards on the product. Do not use

the product if the guards are not in place and working

correctly.

■ The lower blade guard should only open when the blade

is lowered to the workpiece and must always be able to

move freely and close automatically.

■ Always fix and use extension bars for workpiece support

during operation.

■ Never alter of modify the product or its function. Your

safety may be compromised.

■ Do not use saw blades which are cracked, damaged or

deformed.

■ Do not use saw blades made of high-speed steel.

■ Only use blades that are sharp. Replace dull blades.

■ Always use blades with correct size and shape of arbour

holes. Blades that do not match the mounting hardware

of the saw will run eccentrically, causing loss of control.

■ Use only woodworking blades specified in this manual,

which comply with EN 847-1.

■ Do not use any flanges, washers and nuts to secure the

saw blade other than those supplied or indicated in the

instruction manual.

■ It is necessary to select a saw blade which is suitable

for the material being cut. Never use the product to cut

materials other than those specified in the intended use

section in this manual.

■ It is important to avoid overheating the blade and melting

the plastic when cutting.

■ It is essential to adhere to the maximum speed specified

on the saw blade, only use saw blades that are marked

with a speed equal or higher than the speed marked on

the tool.

■ Replace the table insert when worn or damaged.

■ Before work, make a dummy cut without the motor turned

on so the position of the blade, operation of the guards

with respect to other machine parts, and workpiece may

be checked.

■ When performing mitre, bevel or compound mitre cuts,

adjust the sliding fence or sub-fence to ensure the

correct clearance from the blade.

■ Avoid uncontrolled release of the saw unit from the fully

down position.

■ The handle lock must always be engaged when

transporting the product.

■ Keep the floor area free of loose materials, such as chips

and cut-offs.

■ Refrain from removing any cut-offs or other parts of the

workpiece from the cutting area whilst the product is

running and the saw head is not in the rest position.

■ Long workpieces must be adequately supported. The

working area of the saw includes the whole extent of the

workpiece. The operator should secure this area from

accidental contact from other persons or objects which

may move the workpiece during operation.

■ The dust produced when using the product may be

harmful to health. Use a dust suction system and wear

a suitable dust protection mask. Remove deposited dust

thoroughly with a vacuum cleaner.

■ It may be necessary to adjust the sliding fence to ensure

proper clearance prior to making a bevel or compound

cut. Make sure the sliding fence lock screw is tightened

securely after the adjustment.

■ The clamp can be installed and used on either side of

the blade. In some operation, the clamp may interfere

with the blade guard assembly. Always make sure there

is no interference with the blade guard prior to beginning

any cutting operation to reduce the risk of serious

personal injury.

■ Ambient temperature range for tool during operation is

between 0 ˚C and 40˚ C.

■ Ambient temperature range for tool storage is between

0 ˚C and 40˚ C.

■ The recommended ambient temperature range for the

charging system during charging is between 10 ˚C and

38˚ C.

ADDITIONAL BATTERY SAFETY WARNINGS

■ To reduce the risk of fire, personal injury, and product

damage due to a short circuit, never immerse your

tool, battery pack or charger in fluid or allow a fluid to

flow inside them. Corrosive or conductive fluids, such

as seawater, certain industrial chemicals, and bleach

or bleach-containing products, etc., can cause a short

circuit.

■ Ambient temperature range for battery during use is

between 0 ˚C and 40˚ C.

■ Ambient temperature range for battery storage is

between 0 ˚C and 20˚ C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national

provisions and regulations.

Follow all special requirements on packaging and labelling

when transporting batteries by a third party. Ensure that

no batteries can come in contact with other batteries

or conductive materials while in transport by protecting

exposed connectors with insulating, non-conductive caps or

tape. Do not transport batteries that are cracked or leaking.

Check with the forwarding company for further advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still

impossible to completely eliminate certain residual risk

factors. The following hazards may arise and the operator

should pay special attention to avoid the following:

■ Risk of contact with uncovered parts of the rotating saw

blade

■ Kick-back of workpieces or parts of workpieces due to

improper adjustment or handling

■ Catapulting of faulty carbide tips from the saw blade

■ Damage to the respiratory system

NOTE: Wear respiratory protection masks containing

filters appropriate to the materials being worked. Ensure

adequate workplace ventilation. Do not eat, drink or

smoke in the work area.

■ Damage to hearing if effective hearing protection is not

worn.

WARNING! Dust from certain paints, coatings and

materials may cause irritation or allergic reactions to the

6

Original Instructions

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Ryobi RMS18254X-0 Fierastrau circular stationar. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Ryobi. S-ar putea să ofere un manual original. Căutați manualul dvs. Ryobi RMS18254X-0 Fierastrau circular stationar într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Ryobi Fierastraie circulare stationare
Mai multe manuale pentru Fierastraie circulare stationare

Întrebări frecvente despre Ryobi RMS18254X-0 Fierastrau circular stationar

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Ryobi EMS190DC Fierastrau circular stationar

Manual

Ryobi ETMS1825 Fierastrau circular stationar

Manual

Ryobi RMS18190-0 Fierastrau circular stationar

Manual

Ryobi R18MS216-0 Fierastrau circular stationar

Manual

Skil 3590 CA Fierastrau circular stationar

Manual

Asist AE5P180NL Fierastrau circular stationar

Manual

Bosch GCM 8000 SJ Professional Fierastrau circular stationar

Manual

Parkside IAN 273098 Fierastrau circular stationar

Categorii relevante