Manual Skil 2470 AA Maşină de găurit-înşurubat

Manual

8

• The charger is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning use of the charger by a person

responsible for their safety

• Ensure that children do not play with the charger

• Do not use charger when damaged; take it to one of the

offi cially registered SKIL Service Stations for a safety

check

• Do not use charger when cord or plug is damaged; cord

or plug should be replaced immediately at one of the

offi cially registered SKIL Service Stations

• Do not disassemble charger or tool

• Explanation of symbols on charger/battery

3 Read the instruction manual before use

4 Only use the charger indoors

5 Double insulation (no earth wire required)

6 Do not dispose of the charger together with

household waste material

7 Do not dispose of the battery together with

household waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the

plug

• If for any reason the old plug is cut off the cord of the

charger, it must be disposed of safely and not left

unattended

USE

• On/off 8

• Speed control for smooth starting 9

• Charging battery 2

! a lithium-ion battery that is new or has not been

used for a longer period does not develop its full

capacity until after approximately 3 charging/

discharging cycles

- plug charger into power source

- light C will turn on GREEN indicating that the charger

is ready for operation

- insert tool into charger

- light C will turn RED indicating that the battery is

being charged

- after 3-5 hours the battery is fully charged and

charging automatically stops (light C will turn GREEN

again)

- the tool may be used, even though light C may still

be RED (the light may require more than 3 hours to

turn GREEN depending on temperature)

- if the tool is used only briefl y, the charging time can

be very short

- unplug the charger when the battery is fully charged

IMPORTANT:

- if light C does not turn RED after inserting tool into

charger, this may mean that the battery is too cold or

too hot; when the battery temperature returns to

between 0°C and 45°C, the charger will automatically

begin charging

- the lithium-ion battery can be charged at any time

(interrupting the charging procedure does not

damage the battery)

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- do not charge at temperatures below 0°C and over

45°C; this will seriously damage the battery as well

as the charger

- when the lithium-ion battery is empty, the tool is

switched off automatically

! do not continue to press the on/off switch after

the tool is switched off automatically; battery may

be damaged

- the battery must be kept separate from the natural

environment and should not be disposed of as

normal domestic waste (symbol 7 will remind you of

this when the need for disposing occurs)

• Changing direction of rotation 0

- indicator E shows the selected direction of rotation

- when not properly set in left/right position, switch

A 2 cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits !

- only use 1/4” hexagonal shank accessories with

locking groove

! always use screw bits in combination with a bit

holder

- pull accessory to check that it is locked correctly

! do not use bits with a damaged shank

! only use sharp bits

• Torque control (VariTorque) @

- output torque will increase as clutch ring G is rotated

from 1 to 10; position H will lock up the clutch to

permit drilling or driving heavy duty work

- when turning in a screw, fi rst try VariTorque position 1

and increase until the desired depth has been

reached

• Low battery level indicator #

When battery level is low, indicator J lights on

• Mounting charger on the wall $

• Holding and guiding the tool

! while working, always hold the tool at the grey-

coloured grip area(s) %

- keep ventilation slots K 2 uncovered

- do not apply too much pressure on the tool; let the

tool do the work for you

APPLICATION ADVICE

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

of the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Skil 2470 AA Maşină de găurit-înşurubat. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Skil. S-ar putea să ofere un manual original. Căutați manualul dvs. Skil 2470 AA Maşină de găurit-înşurubat într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Skil Maşini de găurit-înşurubat
Mai multe manuale pentru Maşini de găurit-înşurubat

Întrebări frecvente despre Skil 2470 AA Maşină de găurit-înşurubat

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Skil 3020 HA Maşină de găurit-înşurubat

Manual

Skil 3075 HC Maşină de găurit-înşurubat

Manual

Skil 3005 HA Maşină de găurit-înşurubat

Manual

Skil 3020 HB Maşină de găurit-înşurubat

Manual

Skil 3065 CA Maşină de găurit-înşurubat

Manual

Skil 3080 CA Maşină de găurit-înşurubat

Manual

Skil 3021 HC Maşină de găurit-înşurubat

Manual

Skil 3070 HL Maşină de găurit-înşurubat

Categorii relevante