Manual Skil 3065 HB Maşină de găurit-înşurubat

Manual

10

and increase until the desired depth has been reached

• Mechanical gear selection e

- set selector D to desired speed

! actuate the gear selector while tool is running

slowly

1

- low speed

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

2

- high speed

- lower torque

- for drilling small diameters

• WORKLIGHT H r

- WORKLIGHT H will illuminate in default low brightness

mode when the tool is turned on OR if WORKLIGHT

button G is depressed without turning the tool on.

Brightness can be switched from low to full or from full

to low by pressing the WORKLIGHT button G.

- Low brightness – turns o approx. 10s after on/o

switch is released

- High brightness - turns o approx. 600s after on/o

switch is released

! WORKLIGHT button G is disabled while the tool is

running. The brightness should only be switched

when the tool is not running.

! 

protection is activated (see below)

• Battery protection

The tool is suddenly being switched o or prevented from

being switched on, when

- the load is too high --> remove load and restart

- the battery temperature is not within the allowable

operating temperature range of -20 to +50°C --> 2

levels of the battery level indicator start ashing when

pressing button J7c; wait until battery has returned

within the allowable operating temperature range

- the battery is nearly empty (to protect against

deep discharge) --> a low battery level or ashing low

battery level ub is shown by the battery level indicator

when pressing button J; charge battery

! 



damaged

• Holding and guiding the tool t

! while working, always hold the tool at the grey-

coloured grip area(s)

- keep ventilation slots E 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits y

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking

• of the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

an electrical shock)

BATTERIES

• The battery supplied is partially charged (to ensure

full capacity of the battery, completely charge the battery

in the battery charger before using your power tool for the

rst time)

• Only use the following batteries and chargers with

this tool

- SKIL battery: BR1*31****

- SKIL charger: CR1*31****

• Do not use battery when damaged; it should be replaced

immediately

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

- when charging 4...40°C

- during operation –20...+50°C

- during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3

Read the instruction manual before use

4

Batteries may explode when disposed of in re, so do not

burn battery for any reason

5

Store tool/charger/battery in locations where temperature

will not exceed 50°C

6

Do not dispose of electric tools and batteries together

with household waste material

USE

• Combined switch for on/o and speed control A 2

- control the speed steplessly from zero to maximum by

putting less or more pressure on the trigger

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery 2

• Battery level indicator 7

- press the battery level indicator button J to show the

current battery level 7a

! when the lowest level of the battery indicator

7b, the

battery is empty

! 

after pressing button J 7c, the battery is not

within the allowable operating temperature range

• Attaching belt clip 8

- attach the belt clip K to the drill with the supplied screw.

• Integrated bit clip L 2

- conveniently store hex bits.

• Strap xing M 2

- attach a wrist strap (not included) around your hand

when carrying the tool.

• Changing direction of rotation 9

- when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits q

! do not use bits with a damaged shank

• Torque control (VariTorque) w

- output torque will increase as clutch ring B is rotated

from 1 to 17; position C will lock up the clutch to permit

drilling or driving heavy duty work

- when turning in a screw, rst try VariTorque position 1

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Skil 3065 HB Maşină de găurit-înşurubat. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Skil. S-ar putea să ofere un manual original. Căutați manualul dvs. Skil 3065 HB Maşină de găurit-înşurubat într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Skil Maşini de găurit-înşurubat
Mai multe manuale pentru Maşini de găurit-înşurubat

Întrebări frecvente despre Skil 3065 HB Maşină de găurit-înşurubat

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Skil 3011 CA Maşină de găurit-înşurubat

Manual

Skil 3020 HD Maşină de găurit-înşurubat

Manual

Skil 3020 CA Maşină de găurit-înşurubat

Manual

Skil 3070 EB Maşină de găurit-înşurubat

Manual

Skil 3060 HL Maşină de găurit-înşurubat

Manual

Skil 3076 JA Maşină de găurit-înşurubat

Manual

Skil 3065 HC Maşină de găurit-înşurubat

Manual

Skil 2834 AG Maşină de găurit-înşurubat

Categorii relevante