Manual Skil 9006 AA Polizor unghiular

Manual

8

b) Neverplaceyourhandneartherotatingaccessory.

The accessory may kickback over your hand.

c) Donotpositionyourbodyintheareawherepower

toolwillmoveifkickbackoccurs.Kickback will propel

the tool in the direction opposite to the wheel’s movement

at the point of snagging.

d) Usespecialcarewhenworkingcorners,sharp

edgesetc.Avoidbouncingandsnaggingthe

accessory.Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

e) Donotattachasawchainwoodcarvingbladeor

toothedsawblade.Such blades create frequent

kickback and loss of control.

3)SAFETYWARNINGSSPECIFICFORGRINDINGAND

ABRASIVECUTTING-OFFOPERATIONS

a) Useonlywheeltypesthatarerecommendedforyour

powertoolandthespecificguarddesignedforthe

selectedwheel.Wheels for which the power tool was not

designed cannot be adequately guarded and are unsafe.

b) Thegrindingsurfaceofthecentredepressedwheels

mustbemountedbelowtheplaneoftheguardlip. An

improperly mounted wheel that projects through the plane

of the guard lip cannot be adequately protected.

c) Theguardmustbesecurelyattachedtothepower

toolandpositionedformaximumsafety,sotheleast

amountofwheelisexposedtowardstheoperator.

The guard helps to protect the operator from broken

wheel fragments, accidental contact with wheel and

sparks that could ignite clothing.

d) Wheelsmustbeusedonlyforrecommended

applications.For example: Do not grind with the side of

a cut-o wheel. Abrasive cut-o wheels are intended for

peripheral grinding; side forces applied to these wheels

may cause them to shatter.

e) Alwaysuseundamagedwheelflangesthatareof

correctsizeandshapeforyourselectedwheel.

Proper wheel anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-o

wheels may be dierent from grinding wheel anges.

f) Donotuseworndownwheelsfromlargerpowertools.

A wheel intended for a larger power tool is not suitable for

the higher speed of a smaller tool and may burst.

4)ADDITIONALSAFETYWARNINGSSPECIFICFOR

CUTTING OFF OPERATIONS

a) Donot“jam”thecut-offwheelorapplyexcessive

pressure.Donotattempttomakeanexcessivedepth

ofcut.Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheel breakage.

b) Donotpositionyourbodyinlinewithandbehind

therotatingwheel.When the wheel, at the point of

operation, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

c) Whenthewheelisbindingorwheninterruptingacut

foranyreason,switchoffthepowertoolandholdthe

powertoolmotionlessuntilthewheelcomestoa

completestop.Neverattempttoremovethecut-off

wheelfromthecutwhilethewheelisinmotion,

otherwisekickbackmayoccur.Investigate and take

corrective action to eliminate the cause of wheel binding.

d) Donotrestartthecuttingoperationinthe

workpiece.Letthewheelreachfullspeedand

carefullyre-enterthecut.The wheel may bind, walk up

or kickback if the power tool is restarted in the workpiece.

e) Supportpanelsoranyoversizedworkpieceto

minimizetheriskofwheelpinchingandkickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

f) Useextracautionwhenmakinga“pocketcut”into

existingwallsorotherblindareas.The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

GENERAL

• This tool is not suitable for wet grinding/cutting

• Only use the anges which are supplied with this tool

• This tool should not be used by people under the age of

16 years

• Alwaysdisconnectplugfrompowersourcebefore

makinganyadjustmentorchanginganyaccessory

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

• Useonlygrinding/cuttingdiscswithamaximum

thicknessof8mmandaspindleholediameterof

22mm

• Never use reducors or adaptors to t large-hole grinding/

cutting discs

• Never use accessories with a “blind” threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

• Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

BEFORE USE

• Before using the tool for the rst time, it is recommended

to receive practical information

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Always mount auxiliary handle E 6 and protective guard

F 6; never use the tool without them

• Usesuitabledetectorstofindhiddenutilitylinesor

callthelocalutilitycompanyforassistance (contact

with electric lines can lead to re or electrical shock;

damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Donotworkmaterialscontainingasbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wearadustmaskandworkwithadust

extractiondevicewhenconnectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wearadustmaskand

workwithadustextractiondevicewhenconnectable

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Skil 9006 AA Polizor unghiular. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Skil. S-ar putea să ofere un manual original. Căutați manualul dvs. Skil 9006 AA Polizor unghiular într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Skil Polizoare unghiulare
Mai multe manuale pentru Polizoare unghiulare

Întrebări frecvente despre Skil 9006 AA Polizor unghiular

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Skil 3920 CA Polizor unghiular

Manual

Skil 9130 AA Polizor unghiular

Manual

Skil 1043 AA Polizor unghiular

Manual

Skil 9132 AB Polizor unghiular

Manual

Skil 9003 AD Polizor unghiular

Manual

Skil 9134 AB Polizor unghiular

Manual

Skil 9132 AA Polizor unghiular

Manual

Skil 3921 CA Polizor unghiular

Categorii relevante