Manual Tryton THL2000B Suflanta cu aer cald

Manual

8

Sound pressure value measured is lower than 70 dB (A).

maintenance operations (e.g.

BEFORE YOU START:

inspections, cleaning, adjustments)

1. Make sure that power supply parameters meet the requirements

always unplug the power cord from

provided on the tool nameplate.

2. Make sure the tool switch is in off position. Connecting the tool to the

the mains socket.

mains socket when its switch is in on position can result in serious

accident, as the hot air gun starts immediately.

g) Never allow children to use the tool.

3. When your workplace is too far to plug the tool directly to the mains

APPLICATIONS AND CONSTRUCTION:

socket, use an extension cord with a cable cross-section meeting the

tool requirements. Extension cords should be as short as possible.

The hot air gun is a portable power tool. It features small dimensions,

When in use extension cords must be fully uncoiled.

ergonomic design, low noise emission, high speed air flow, adjustment

of operating temperature and speed of airflow.

DURING OPERATION:

The tool is intended for removing paint coats, shaping and welding

n Switching on/off

plastics and fitting shrinking plastic tubing. It can be also used to soften

To switch on the tool set the on/off switch/ operation mode selector (3)

adhesives and defrost water pipes.

to position I, II or III.

WARNING! The appliance is not intended to be operated by

ź To switch the tool off set the on/off switch/ operation mode selector

means of an external timer or separate remote-control system.

(3) to position O.

Do not use the tool in professional applications. Any use in

n Setting operation mode

applications other than indicated is prohibited and results in making the

warranty void and null and waiving manufacturer's liability for any

The on/off switch/ operation mode selector (3) can be set in three

resulting damage.

positions.

Any modification to the tool carried out by the user waives

The air flow and temperature required can be adjusted by using the table:

manufacturer's liability for damage to the tool, user or other property.

Specific residual risks cannot be eliminated despite proper use. The

following threats may occur resulting from the design and structure of

the machine:

- Injury from contact with hot parts;

- Ejection of a workpiece or its parts.

n The set includes:

ź Hot air gun - 1 piece

NOTE: After changing from higher to lower temperature always allow the

ź User's manual - 1 piece

tool to cool down.

ź Warranty card - 1 piece

Temperature adjustment

n Tool components (see Fig. A):

The numbering of tool components refers to graphics presented on page 2

of the user's manual:

1. Outlet nozzle

see Fig. A

2. Operating temperature control

WORKING TIPS:

3. On/off switch/ Operation mode selector

NOTE! Avoid holding the tool perpendicularly to surface

4. Power cord

processed. It results in hot air reflection and sucking it back by

the motor rotor. It results in increasing temperature inside the

TECHNICAL DATA:

motor and damage to the tool. The hot air gun should be held at an angle of

approx. 45º to the surface processed.

The distance between the nozzle and object processed depends on the

material, but cannot be lower than 5 cm.

Before you turn the tool off, set the temperature to minimum and select

the maximum air flow for a short period (more than ten seconds) to cool

down the heating element. It will extend the life of your tool.

n Putting the tool aside

To cool the hot tool down or to have both hands free, put the hot air gun

vertically onto a horizontal surface (see Fig. B).

NOTE: Be especially careful when working with the tool aside! There's a risk

n Noise emission information

of burns caused by its hot nozzle or hot air stream.

The operation mode I is suitable for cooling down heated objects or for

drying a paint coat. It can be also used to cool the tool before putting in

storage or replacing its nozzle (spare nozzles not provided).

n

Temperature can be adjusted only in hot air mode II or III. The target

temperature can be increased by rotating the operating temperature

control (2) clockwise. It is decreased by rotating the control

anticlockwise ( ).

Frequency

50/60 Hz

Power consumption

2000W

Operating temperature Air

flow

/

50 / 250 l/min

º

C

Voltage

220-240 V

Device class

Weight

0,9 kg

II

mode I

mode II

mode III

50 / 250 l/min

- º

450 C

90 / 500 l/min

- º

600 C

Operation mode I

250 l/min - 50 C

º

Operation mode II

250 l/min -

º

50-450 C

Operation mode III

500 l/min -

º

90-600 C

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Tryton THL2000B Suflanta cu aer cald. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Tryton. S-ar putea să ofere un manual original. Căutați manualul dvs. Tryton THL2000B Suflanta cu aer cald într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Tryton Suflante cu aer cald
Mai multe manuale pentru Suflante cu aer cald

Întrebări frecvente despre Tryton THL2000B Suflanta cu aer cald

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Steinel HL 2020 E Suflanta cu aer cald

Manual

Parkside IAN 86585 Suflanta cu aer cald

Manual

Dedra DED7971 Suflanta cu aer cald

Manual

Neo Tools 04-710 Suflanta cu aer cald

Manual

FERM HAM1014 Suflanta cu aer cald

Manual

My Project MJHG023 Suflanta cu aer cald

Manual

AEG BHG 180 Suflanta cu aer cald

Manual

Ryobi EHG2000LCD Suflanta cu aer cald

Categorii relevante