Manual Tryton TXV14LK2 Maşină de găurit-înşurubat

Manual

PREPARATION FOR WORK:

Prior to each use of the tool one has to check whether moving parts of the

device are in operating conditions, not seized, cracked or damaged that

may affect proper operation of the tool. Damaged tools must be handed

over for repairs before they can be used again.

n Shifting gear (Fig. A1)

The gear shifter (3) makes it possible to choose 2 rotation speed ranges.

Gear I: Used for driving and unscrewing screws.

Gear II: Used for drilling.

CAUTION: Do not change the position of the gear shifter (3) during tool

operation as this may damage the gear box. Always allow the tool to come

to a full stop before changing the setting of the gear shifter.

If the gear shifter does not move all the way, move the drive spindle

slightly.

n Changing the chuck (Fig. G)

1. Disconnect the battery (7) from the driver.

2. Open the chuck as much as possible (1)

3. Using a PH 2 (Philips No.2) screwdriver, rotate the fixing screw of the

chuck clockwise (CAUTION! Left-thread). To free a seized bolt hit is

gently on its head.

4. Use a spanner or a Torx T45 screwdriver to unscrew the handle of the

drill/screwdriver anticlockwise.

CAUTION: A jammed keyless chuck (1) can be released by inserting the

short end of a hex key in the chuck and lightly tapping the longer arm of

the key (see Fig.D).

5. To attach the chuck, screw it onto the drive spindle counter-clockwise

(looking from the chuck side) and secure by screwing in the fixing

screw counter-clockwise using a PH 2 screwdriver (No.2 Philips).

n

џ The body of the drill/screwdriver is provided with a battery indicator

(9) that enables to continuously monitor the battery charge status.

Depress the indicator button to check the battery status.

џ The drill/driver is equipped with an auxiliary light (11) for the area of

drilling/driving, which turns on after the appropriate switch (10) is

pushed.

CAUTION: Disconnect the battery from the driver or put the rotation

direction switch (4) in the middle position to secure the machine from being

started by mistake, which could in turn cause harm to the user.

Using a given setting (from 1 - 19) means that the clutch is set to an

assigned toque. This makes it possible to prevent a screw from being

driven too far or being damaged. Different torques should be used for

different screws and materials.

Always start with a low torque and increase gradually until the desired

result is achieved.

n Charging the battery

The driver is supplied with a partially charged battery. Charge the battery

For drilling in metal, wood or plastic, set the ring (2), so that the indicator

fully before use. It is recommended that the first charging session lasts at

(13) points to symbol (14).

least 1 hour.

Press the battery lock button (8), slide the battery out (7) (Fig. B) and

insert into charger socket (12) (Fig. C). Connect charger to an electrical

socket 230 V ~50Hz.

n Battery charging indicator

A green LED light indicates that the charger is connected to a power

source.

A red light flashing with a frequency of about 1/s (1Hz) indicates that

charging is in progress.

Once the battery is fully charged, the red light stops flashing and both,

red and green, lights are lit continuously.

The charging current is lowered automatically as charging progresses.

After approx. 1 hour the charging current is stabilised at a minimum level

(trickle charging), which prevents battery overcharging and damage.

After charging, disconnect the charger and remove the battery.

The lithium-ion battery can be charged at any moment, without

detriment to its life. Interrupting the charging process does not entail a

risk of damaging the battery cells.

IN USE:

n Turning on/off

The switch (10) has fluid rotation speed adjustment built-in.

Press the switch to activate the power tool. The rotation speed will

increase the further the switch is pushed. To stop the power tool, release

Auxiliary components

the switch.

n Choosing rotation direction (Fig. E)

The driver can work with clockwise (right) or counter-clockwise (left)

rotation.

- to select clockwise rotation, move the clockwise/counter-clockwise

slider (4) to the right (looking from the back of the driver),

- to select counter-clockwise rotation, move the clockwise/counter-

n Installation and removing drills to/from the keyless chuck

clockwise slider (4) to the left (looking from the back of the driver),

When the rotation direction switch is in the middle position, it is locked.

For drilling and driving screws in, clockwise operation should be

selected. For taking out the drill bit, removing a stuck drill bit, or

When the tool trigger (10) is released the drill chuck is locked. It enables

unscrewing screws, counter-clockwise operation should be selected.

quick, easy and convenient replacement of a working tool installed in the

n Choosing torque (Fig. F)

drill chuck. To remove a drill (or a working bit) from the drill chuck, rotate

The driver is equipped with a ring (2), which can be used for setting the

the chuck ring anticlockwise to expand the opening of the chuck. Insert a

toque when driving screws. The ring has 19 settings, from 1 to 19, and a

new drill (or a working bit) into the chuck and rotate the chuck ring

drilling setting.

clockwise to secure the drill in the drill chuck.

6

The vibration level value given refers to basic application of the tool. If the tool is used for other applications or with other tools, or if it is not maintained

properly, the vibration level may differ from the values given. The above-mentioned causes may lead to higher exposure to vibrations during the whole

work time.

One must implement additional safety measures to protect the operators from exposure to vibrations, such as maintenance of the electric tool and work

tools, assurance of proper hand temperature, or determination of the sequence of work operations.

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Tryton TXV14LK2 Maşină de găurit-înşurubat. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Tryton. S-ar putea să ofere un manual original. Căutați manualul dvs. Tryton TXV14LK2 Maşină de găurit-înşurubat într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Tryton Maşini de găurit-înşurubat
Mai multe manuale pentru Maşini de găurit-înşurubat

Întrebări frecvente despre Tryton TXV14LK2 Maşină de găurit-înşurubat

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Tryton TUV14LB2 Maşină de găurit-înşurubat

Manual

Tryton TXV18LK2 Maşină de găurit-înşurubat

Manual

Tryton TUV18BK2 Maşină de găurit-înşurubat

Manual

Tryton TUV12BK2 Maşină de găurit-înşurubat

Manual

Tryton TUV14BK2 Maşină de găurit-înşurubat

Manual

Tryton TUV18LB2 Maşină de găurit-înşurubat

Manual

Skil 3018 CA Maşină de găurit-înşurubat

Manual

Skil 3070 HL Maşină de găurit-înşurubat

Categorii relevante