Manual EGO CS1814E Ferăstrăul cu lanţ

Manual

56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS1810E 9

EN

3. Lay the saw chain in a loop on a flat surface and

straighten any kinks (Fig. C).

4. Place the chain drive links into the guide bar groove at

the tip of the guide bar and make the chain a loop at

the back of the guide bar (Fig. D).

5. Hold the chain in position on the guide bar and place

the loop around the sprocket of the saw , and insert

the rest of the chain into the guide bar groove at the

rear part of the guide bar (Fig. E1).

B-1 Side-cover Knob E-1 Drive Sprocket

B-2

Chain-tensioning

Knob

E-2

Chain-tensioning

Pin

D-1 Chain Drive Links E-3 Fastening Bolt

D-2 Guide Bar Groove E-4 Alignment Pin

NOTICE: When looping the saw chain onto the guide

bar, make sure that, after mounting the guide bar onto

the saw, the cutter orientation matches the cutter icon

and rotation direction arrow on the housing of the saw.

If they face in opposite directions, reassemble the saw

chain onto the guide bar with the cutters facing the same

direction (Fig. E2).

6. Place the guide bar onto the chain saw housing by

sliding the guide-bar slot over the fastening bolt and

alignment pin.

7. Turn the chain-tensioning knob to move the chain-

tensioning pin, so that it inserts into the lower pin hole

in the guide bar.

8. Attach the side cover to the housing so that the holes/

pins and fastening bolt/thread hole are aligned with

each other properly (Fig. E3). Lightly tighten the side-

cover knob by turning it clockwise. The bar must be

free to move for tension adjustment.

NOTE: The side-cover knob may not sit completely flat

because the rotation causes the rib underneath to not

engage.

NOTICE:

To extend the guide bar life, invert the bar

occasionally.

ADJUSTING THE CHAIN TENSION

◾ Stop the motor and remove the battery pack before

adjusting the chain tension. Turn the chain-tensioning

knob clockwise or counterclockwise to adjust chain

tension (Fig. F) until the chain seats snugly against the

guide bar with the drive links in the guide bar groove.

◾ A cold chain is correctly tensioned when there is no

slack on the underside of the guide bar and the chain

is snug, but it can be turned by hand without binding.

The chain must be re-tensioned whenever the flats on

the drive links do not sit in the bar groove.

◾ During normal saw operation, the temperature the

chain will increase. The drive links of a correctly

tensioned warm chain will hang approximately 1.3 mm

out of the bar groove (Fig. G).

NOTICE: New chains tend to stretch; check chain tension

frequently and tension as required.

NOTICE: A chain tensioned while it is warm may be too

tight upon cooling. Check the cold tension before next use.

OPERATION

WARNING: Do not allow familiarity with this product

to make you careless. Remember that a careless fraction

of a second is sufficient to inflict serious injury.

WARNING: Do not use any attachments or

accessories not recommended by the manufacturer of

this product. The use of attachments or accessories not

recommended can result in serious personal injury.

WARNING: To prevent accidental starting that could

cause serious personal injury, always remove the battery

pack from the machine when assembling parts, making

adjustments, cleaning, or when not in use.

Before each use, inspect the entire product for damaged,

missing, or loose parts, such as screws, nuts, bolts, caps,

etc. Securely tighten all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced.

APPLICATION

You may use this product for basic felling, limbing, pruning,

and woodcutting of lumber and trees.

NOTICE: The machine is to be used only for its prescribed

purposes. Any other use is deemed to be a case of misuse.

FILLING BAR AND CHAIN LUBRICANT

WARNING: Do not smoke or bring any fire or flame

near the oil or the chain saw. Oil may spill and cause a

fire.

NOTICE: The chain saw is not filled with oil at the time of

purchase. It is essential to fill the tank with oil before use.

The chain is automatically lubricated with chain oil during

operation.

1. Position the chain saw on its side with the tank cap

facing upwards.

2. Clean the oil tank cap and the area around it to ensure

that no dirt falls into the oil tank.

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru EGO CS1814E Ferăstrăul cu lanţ. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați EGO. S-ar putea să ofere un manual original. Căutați manualul dvs. EGO CS1814E Ferăstrăul cu lanţ într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru EGO Ferăstraie cu lanţ
Mai multe manuale pentru Ferăstraie cu lanţ

Întrebări frecvente despre EGO CS1814E Ferăstrăul cu lanţ

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

EGO CSX5000 Ferăstrăul cu lanţ

Manual

EGO CS1401E Ferăstrăul cu lanţ

Manual

EGO CSX3002 Ferăstrăul cu lanţ

Manual

EGO CS1810E Ferăstrăul cu lanţ

Manual

EGO PS1000E Ferăstrăul cu lanţ

Manual

EGO CSX3000 Ferăstrăul cu lanţ

Manual

EGO PS1003E Ferăstrăul cu lanţ

Manual

EGO CS1200E Ferăstrăul cu lanţ

Categorii relevante