LINE TRIMMER ATTACHMENT — STA15008
MAINTENACE AND STORAGE
◾ Disconnect the machine from the power supply
(i.e. remove the battery pack) before carrying out
maintenance or cleaning work.
◾ Use only the manufacturer’s recommended
replacement parts and accessories.
◾ Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
◾ When not in use, store the machine out of the reach
of children.
OTHER SAFETY WARNINGS
◾ Avoid Dangerous Environments – Don’t use
appliances on damp or wet slope.
◾ Keep guards in place and in working order.
◾ Keep hands and feet away from the cutting area.
◾ To reduce the risk of injury, never work on a ladder
or on any other insecure support. Never hold the
cutting unit above waist height.
◾ Check the cutting unit at regular short intervals
during operation, or immediately if there is a
noticeable change in cutting behavior.
◾ For best results, your battery should be charged in a
location where the temperature is greater than 5° C
and less than 40° C. Do not store it outside or in vehicles.
◾ If you are approached, stop the motor and cutting unit.
◾ Warn the operator of the danger of blade thrust
(only using with 3-teeth blade).
◾ Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾ Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾ Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾ Blade thrust is more likely to occur in areas where it
is difcult to see the material being cut.
◾ Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to y off and
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade
A dull blade is more likely to snag and thrust
(only using with 3-teeth blade).
◾ A coasting blade/line can cause injury while it
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade/line has completely stopped rotating.
◾ Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾ Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾ If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
◾ Use only with battery packs and chargers listedin g.A
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
Cutting Mechanism Bump Head
Line Diameter
2.4 mm nylon
twist line
Cutting Width 38 cm
No-Load Speed 5000/6000 min
-1
Weight (Without battery pack) 1.59 kg
Recommended Operating
Temperature
0°C-40°C
Recommended Storage Temperature -20°C-70°C
Measured sound power level L
WA
94.6 dB(A)
K=1.80 dB(A)
Sound pressure level at operator’s
ear L
PA
83.2 dB(A)
K= 3 dB(A)
Guaranteed sound power level L
WA
(measured according to
2000/14/EC)
96 dB(A)
Valuation of
vibration a
h
Front-assist handle
1.1 m/s
2
K=1.5 m/s
2
Rear handle
1.4 m/s
2
K=1.5 m/s
2
◾ The above parameters are tested and measured
equipped with power head PH1400E.
◾ The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
◾ The declared vibration total value may also be used in
a preliminary assessment of exposure.
NOTICE: The vibration emission during actual use of the
power tool can differ from the declared value in which the
tool is used; In order to protect the operator, user should wear
gloves and ear protectors in the actual conditions of use.
Alăturați-vă conversației despre acest produs
Aici puteți împărtăși ce părere aveți despre EGO STA1500 Trimmer de gazon. Dacă aveți o întrebare, citiți mai întâi cu atenție manualul. Solicitarea unui manual se poate face folosind formularul nostru de contact.