Manual Hitachi DS 14DBEL Maşină de găurit-înşurubat

Manual

6

English

NOTE

The recharging time may vary according to the ambient

temperature and power source voltage.

<UC18YML2>

Especially, using a DC 12V in-car power source may

require longer recharging time at high temperatures.

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the

receptacle or cigarette lighter socket.

5. Hold the charger fi rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used,

the pilot lamp of the charger lights up green or lights

for 1 second, does not light for 0.5 seconds (off for

0.5 seconds). In such a case, fi rst let the battery cool,

then start charging.

○ When the pilot lamp fl ickers in red (at 0.2-seconds

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

○ Since the built-in micro computer takes about 3

seconds to confi rm that the battery being charged with

charger is taken out, wait for a minimum of 3 seconds

before reinserting it to continue charging. If the battery

is reinserted within 3 seconds, the battery may not be

properly charged.

○ Check the voltage of the in-car power source when

the pilot lamp fl ickers in green (every 0.2 seconds)

continuously. (UC18YML2)

If the voltage is 12V or lower, it indicates that the car

battery has weakened and cannot be charged.

○ If the pilot lamp does not blink in red (every second) even

though the charger cord or cigarette lighter connecting

plug is connected to the power, it indicates that the

protection circuit of the charger may be activated.

● Regarding the temperatures and charging time of the battery.

The temperatures and charging time will become as shown in Table 2

Table 2

Charger

Battery

UC18YFSL

UC18YML2

(AC/DC)*

1

Charging voltage V 14.4 V – 18 V

Weight kg 0.5 0.7

Temperatures at which the battery can be

recharged

0oC – 50oC

Charging time for battery capacity, approx.

(At 20oC)

1.3 Ah

1.5 Ah

2.0 Ah

2.5 Ah

3.0 Ah

4.0 Ah

5.0 Ah

min.

min.

min.

min.

min.

min.

min.

20

22

30

35

45

60

75

20/50

22/60

30/80

35/100

45/120

60/160

75/200

Number of battery cells 4 – 10

*

1

AC power supply / DC 12V (in-car) power supply

Remove the cord or plug from the power and then

connect it again after 30 seconds or so. If this does

not cause the pilot lamp to blink in red (every second),

please take the charger to the Hitachi Authorized Service

Center.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the

battery

1 166

Charging 2 166

Tightening torque adjustment 3 166

Selecting the drill position 4 166

Selecting the impact position 5 166

Change rotation speed 6 166

Removing and mounting the hook 7 167

How to use the LED light 8 167

Mounting the bit 9 167

Reversing the rotational direction 10 167

Switch operation 11 167

Selecting accessories ― 168

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade effi ciency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

0000Book̲DS14DBEL.indb60000Book̲DS14DBEL.indb6 2014/10/149:51:112014/10/149:51:11

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hitachi DS 14DBEL Maşină de găurit-înşurubat. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hitachi. S-ar putea să ofere un manual original. Căutați manualul dvs. Hitachi DS 14DBEL Maşină de găurit-înşurubat într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Hitachi Maşini de găurit-înşurubat
Mai multe manuale pentru Maşini de găurit-înşurubat

Întrebări frecvente despre Hitachi DS 14DBEL Maşină de găurit-înşurubat

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Hitachi DS 12DVFA Maşină de găurit-înşurubat

Manual

Hitachi DS 10DAL Maşină de găurit-înşurubat

Manual

Skil 3018 RC Maşină de găurit-înşurubat

Manual

Skil 3018 CA Maşină de găurit-înşurubat

Manual

Skil 3070 FA Maşină de găurit-înşurubat

Manual

Skil 3010 EA Maşină de găurit-înşurubat

Manual

Skil 3021 CA Maşină de găurit-înşurubat

Manual

Parkside IAN 356349 Maşină de găurit-înşurubat

Categorii relevante