Manual Hozelock 2490 Auto Reel Tambur pentru furtun de grădina

Manual

5

(Fig.1)

A. 93273 - Auto Reel

B. 83360 - Wall Bracket

C. 93411 - Feeder Hose

D. 2175 - Threaded tap connector

E. 2166 - Hose End Connector

F. 2185 - Waterstop Connector

G. 53025 x4 - Wall Plug

H. 53112 x4 - Screws

I. 2292 - Hose Nozzle

J. 83304 - Side Disc

TOOLS NEEDED:

• Flat-ended screwdriver

• Philips screwdriver

• Tape measure

• Ø7mm masonry drill bit

• Electric drill

• Spirit Level

FIT THE WATER INLET HOSE

Fig 1.

A. One side of the reel has its side disc already removed.

Lay the reel on a soft surface with this side uppermost.

B. Two screws hold in place the plate on the internal hose

connector. Unscrew them.

C. Pass the 2 metre water inlet hose through the opening

from the outside to the inside of the casing. Unscrew

the large hose nut connector and put it on the hose.

Push the hose under the teeth of the small clasp.

Tighten the hose nut. Screw the internal hose

connector back in place.

D. Fit the side disc. Attach the 2166 hose end connector

to the free end of the water inlet hose. Attach the

2185 water stop connector to the watering hose.

If the water inlet hose supplied is too short to reach

your tap, replace it with a good quality 13mm (1/2”)

hose.

SELECT A SUITABLE POSITION FOR

INSTALLATION

Fig. 2

The reel is designed for external use only and is not

suitable for use with indoor taps.

The reel should be able to swivel through 180º. Allow

50cm of clearance on both sides of the wall bracket.

If the hose is to be used around corners, mount the reel

at least 1m from the corner and use a hose guide, part

no. 2392, which is not supplied.

FIX THE WALL BRACKET

Fig 3.

Important: Ensure that the bracket is vertical.

Use the four plugs and screws supplied. The plugs and

screws supplied are designed for use on standard brick

and concrete or timber walls only. To fix the bracket to

any other surface, you should use screws and plugs

appropriate for that surface.

INSTALLING THE REEL

Fig 4.

1. Align the back of the reel with the wall bracket.

2. Slide the pivot tube through the reel and wall bracket

from the top.

3. Attach the threaded tap connector to your tap and

connect the water inlet hose to it.

4. Attach the 2292 nozzle onto the end of the watering

hose.

Test the assembly to ensure the reel rotates freely

through 180º. Turn the tap on and run the water

through the reel before using it for the first time. Check

for leaks and re-tighten assembled parts if leaks

appear.

A padlock (not supplied) may be fitted to secure the

reel when left unattended on the wall (fig 4A).

Fig 4B.

There is a park point on the top of the pivot tube for

stowage of the water inlet hose end when not in use.

There is an accessory park at the bottom of the bracket

for stowage of hose end accessories.

USING THE SAFETY LOCK

Fig 5.

Operate the safety lock by using the lever on the side of

the reel.

The safety lock has two functions:

1. To stop the hose being pulled out when fully re-wound.

2. To stop accidental rewind while the hose is in use.

To engage the safety lock, turn the lever towards the

symbol. To disengage it, turn the lever so that it

points towards the symbol.

For added security always engage the safety lock when

the reel is unattended.

Do not operate the safety lock while the reel is turning.

USING THE REEL SAFELY

1. To unwind the hose, disengage the safety lock, (see

above) take hold of the hose end and walk away from

the reel in any direction.

2. The reel has an automatic latch to hold the hose in

place at the required length. You will hear 4 latch

‘clicks’ every metre as the hose is unwound.

When the hose is at the required length, stop and

slowly pull the hose until you hear one of the 4 latch

clicks. The hose is now held in place for use, or may be

placed on the ground without rewinding. At this point,

you can engage the safety lock if required.

3. If you need more hose, disengage the safety lock if

necessary, take hold of the hose end and walk away

from the reel with the hose repeating the automatic

latching procedure.

4. The automatic latch is released by pulling the hose

away from the reel past the 4 latch clicks. THE HOSE

GB

Contents

Assembly and installation of

the Auto Reel

Warning

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Hozelock 2490 Auto Reel Tambur pentru furtun de grădina. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Hozelock. S-ar putea să ofere un manual original. Căutați manualul dvs. Hozelock 2490 Auto Reel Tambur pentru furtun de grădina într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Hozelock Tambure pentru furtun de grădină
Mai multe manuale pentru Tambure pentru furtun de grădină

Întrebări frecvente despre Hozelock 2490 Auto Reel Tambur pentru furtun de grădina

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Hozelock 2475 2n1 Tambur pentru furtun de grădina

Manual

Hozelock 2590 Auto Reel Tambur pentru furtun de grădina

Manual

Hozelock 2595 Auto Reel Tambur pentru furtun de grădina

Manual

Hozelock 2476 2n1 Tambur pentru furtun de grădina

Manual

Hozelock 2597 Auto Reel Tambur pentru furtun de grădina

Manual

Hozelock 2398 Tambur pentru furtun de grădina

Manual

Hozelock 2477 2n1 Tambur pentru furtun de grădina

Manual

Hozelock 2416 Compact Cart Tambur pentru furtun de grădina

Categorii relevante