Manual Maestro MR313C Fier de călcat

Manual

6 7

STEAM IRONING

- Filling the reservoir

Please note! Do not use chemical additive, scented substances or decalciers.

- Check that the plug is disconnected from the socket.

- Move the steam selector (3/Picture 1) to “0” (Picture 2.1).

- Open the lid (2/Picture 1)

- Raise the tip of the iron to help the water enter the opening without overowing.

- Slowly pour the water into the water tank Picture 2.2 using the special measure and

taking care not to go over the maximum level indicated by “MAX” on the reservoir

- Close the lid (2/Picture 1).

SELECTING THE TEMPERATURE Picture 2.3

- Put the iron in a vertical position.

- Put the plug in the socket.

- Adjust the thermostat knob (9/Picture 1) according to the international symbol on the

garment label [Table1]. The plate temperature control light (8/Picture 1) indicates that the

iron is heating up. Wait until the plate temperature control light goes off before ironing.

Warning: during ironing, the plate temperature control light (8/Picture 1) comes on at

intervals, indicating that the selected temperature is maintained. If you lower the thermostat

temperature after ironing at a high temperature, do not start ironing until the plate

temperature control light comes on again.

SELECTING THE STEAM Picture 2.1

The quantity of steam is regulated by the steam selector (3/Picture 1).

- Move the steam selector to a position between minimum and maximum depending

on the quantity of steam required and the temperature selected.

Please note: the iron gives off steam continuously only if you hold the iron horizontally.

You can stop the continuous steam by placing the iron in a vertical position or by moving

the steam selector to «0». As indicated on the thermostat knob and in the initial table, you

can only use steam at the highest temperatures. If the selected temperature is too low,

water may drip onto the plate.

Selecting Steam shot and steam when ironing vertically. Pictures 2.4-2.5

Press the steam shot button (5/Picture 1) to generate a powerful burst of steam that can

penetrate the fabrics and smooth the most difcult and tough creases. Wait for a few

seconds before pressing again.

By pressing the steam shot button at intervals you can also iron vertically (curtains, hung

garments, etc.).

Warning: the steam shot function can only be used at high temperatures. Stop the

EN

emission when the plate temperature control light (8/Picture 1) comes on, than

start ironing again only after the light has gone off.

DRY IRONING

To iron without steam, follow the instructions in section “steam ironing”, leaving the steam

selector (8/Picture 1) in the position ”no steam”.

SPRAY FUNCTION Picture 2.6

Make sure that there is water in the water tank. Press the spray button (4/Picture 1) slowly

(for a dense spray) or quickly (for a vaporized spray).

Warning: for delicate fabrics, we recommend moistening the fabric beforehand using the

spray function , or putting a damp cloth between the iron and the fabric. To avoid staining,

spray on silk or synthetic fabrics.

SELF-CLEANING

The self-cleaning feature cleans inside the plate, removing impurities. We recommend

using it every 10-15 days. Directions:

-Fill the reservoir according to the “lling the water reservoir” section.

-Plug the product into a standard electrical outlet near a sink , turn the temperature control

dial the MAX position, rest the heel of the iron on a at, stable surface and allow it to heat

until the temperature light (8/Picture 1) goes out.

-Hold the iron horizontally over the sink and press the button (12/Picture 1) ”self-clean”.

- When the soleplate has cooled down, you can clean it with a damp cloth.

Maintenance and care

Warning!

Before cleaning the iron in any way, make sure that the appliance plug is not connected to

the socket.

Before cleaning unplug the appliance and let it cool completely.

Do not let water get inside the appliance, except the parts are special made for it.

-Avoid scratching the plate with steel wool or metallic objects.

-Any deposits, starch residue or size left on the plate can be removed using a damp cloth

or an unabrasive liquid detergent.

The plastic parts can be cleaned with a damp cloth then wiped over with a dry cloth.

Storage

- Before cleaning unplug the appliance and let it cool completely.

- Turn the temperature control dial and steam adjustment knob to the «0» position.

- Open ller cover, turn appliance upside down and pour out the water.

- Keep the appliance in cool dry place, away from children and persons with reduced

mental or physical abilities Picture 2.8.

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Maestro MR313C Fier de călcat. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Maestro. S-ar putea să ofere un manual original. Căutați manualul dvs. Maestro MR313C Fier de călcat într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Maestro Fiare de călcat
Mai multe manuale pentru Fiare de călcat

Întrebări frecvente despre Maestro MR313C Fier de călcat

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Maestro MR310C Fier de călcat

Manual

Maestro MR304C Fier de călcat

Manual

Maestro MR307С Fier de călcat

Manual

Maestro MR308С Fier de călcat

Manual

Maestro MR301C Fier de călcat

Manual

Maestro MR-320C Fier de călcat

Manual

Maestro MR321C Fier de călcat

Manual

Maestro MR311C Fier de călcat

Categorii relevante