Manual Skil 3420 DA Ferăstrău vertical

Manual

13

• Operating the tool

- before switching on the tool, ensure that front end of

footplate rests at on the workpiece

- hold tool rmly with both hands, so you will have full

control of the tool at all times

! while working, always hold the tool at the grey-

coloured grip area(s)

i

- ensure that complete surface of footplate rests rmly on

the workpiece

! ensure that the blade has come to a complete

standstill, before you lift the tool from the

workpiece

- keep ventilation slots D

2

uncovered

• Battery protection

Switches o the tool or prevents the tool from being

switched on, when

- the load is too high

- the battery temperature is not within the allowable

operating temperature range of -20 to +50°C

- the lithium-ion battery is nearly empty (to protect

against deep discharge)

! 



damaged

APPLICATION ADVICE

• Use the appropriate saw blades

o

! tool accepts most commonly available T-shank

and U-shank blades

q

• When cutting metals, lubricate saw blade regularly with

oil

• For an accurate straight cut, guide tool with footplate

along the edge of a straight piece of wood

p

• Pre-drill a hole before making cut-outs

a

• Splinter-free cutting

- cover cutting-line with several layers of wide tape

before cutting

- always face the good side of the workpiece down

• For more information see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool clean (especially ventilation slots D

2

)

! remove battery from tool before cleaning

• If lever F loosens during use, set the tightness of lever

F

s

- place lever F in middle position

- loosen lock screw L with PH2 screw driver counter

clockwise

- tighten set screw K nger tight with Allen key 4mm

counter clockwise

! set screw K uses left hand thread

- tighten lock screw L with PH2 screw driver clockwise

- tighten lever F

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

- SKIL charger: CR1*31****

• Do not use the battery when damaged; it should be

replaced

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

- when charging 4...40°C

- during operation –20...+50°C

- during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3

Read the instruction manual before use

4

Batteries may explode when disposed of in re, so do not

burn battery for any reason

5

Store tool/charger/battery in locations where temperature

will not exceed 50°C

6

Do not dispose of electric tools and batteries together

with household waste material

USE

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery

2

• Battery level indicator

7

- press the battery level indicator button J to show the

current battery level.

• On/o

8

a

- move the button for switch locking B to the left to unlock

- press switch A to start the tool

- release switch A to stop the tool

• Speed control for smooth starting

9

• Transportation mode

8

b

- release trigger switch A to stop the tool

- put button B in the right position to prevent accidently

switching on the tool

• Changing saw blades

q

! remove battery from tool before making any

adjustments or changing accessories

! insert blade to full depth with teeth facing forward

w

- tool accepts most commonly available T-shank and

U-shank blades

q

• Sawing at 45°

e

• Selecting sawing mode

r

Use lever C

2

for adjusting the orbital action from

accurate cutting (= 0) to fast cutting (= 3)

- 1 setting (“0”) for accurate cutting in all materials,

straight + curved

- 3 settings for fast cutting in dierent materials, straight

cuts only

1 = aluminum, plastic

2 = hard wood

3 = soft wood

! always select “0” when sawing splinter-sensitive

material

• LED-light G

t

LED-light G automatically lights on when activating

switch A

• Switch for dust blowing H

y

• Dust suction

u

- connect vacuum cleaner adapter M to foot

- connect vacuum cleaner hose to vacuum cleaner

adapter M

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Skil 3420 DA Ferăstrău vertical. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Skil. S-ar putea să ofere un manual original. Căutați manualul dvs. Skil 3420 DA Ferăstrău vertical într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Skil Ferăstraie verticale
Mai multe manuale pentru Ferăstraie verticale

Întrebări frecvente despre Skil 3420 DA Ferăstrău vertical

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Skil 4600 AA Ferăstrău vertical

Manual

Skil 4581 CD Ferăstrău vertical

Manual

Skil 4581 CA Ferăstrău vertical

Manual

Skil 4531 GA Ferăstrău vertical

Manual

Skil 1061 AG Ferăstrău vertical

Manual

Skil 4370 AA Ferăstrău vertical

Manual

Skil 4530 GB Ferăstrău vertical

Manual

Skil 3440 JA Ferăstrău vertical

Categorii relevante