Manual Tryton TMT810B Şlefuitor cu bandă

Manual

5

e) Power tools require maintenance. Check power tools for removed from the surrounding area. Sparking can also cause

concentricity or jamming of moving parts, any cracks and all

spontaneous combustion of ding dust in the dust bag (6). Elevated

danger exists when such a dust is mixed with residues of lacquer,

other factors affecting the power tool work safety. If any

polyurethane or other chemical materials, and the ground material is

damage to the power tool is detected, it should be repaired

heated after prolonged grinding. Therefore it is necessary to avoid over-

before use. Improper power tool maintenance is a reason for many

heating of the ground material and the grinder, and the dust bag must

accidents.

always be emptied during breaks and after completion of the work.

f) Cutting tools should be sharp and clean. Keeping sharp cutting

d) Workplace must be kept clean. Mixtures of materials are especially

edges in good condition reduces the risk of jamming and facilitates

dangerous. Light metal dust can ignite or explode.

operation.

e) Aspiration of grinding dust is harmful to health. Direct

g) Power tools, equipment, working tools etc. should be used

physical contact with dusts or their penetration to lungs can

according to this user's manual taking into account

cause allergic reactions and/or respiratory system diseases

operating conditions and the work to be done. Misusing a

of the operator or persons in the vicinity. Some materials,

power tool can result in dangerous situations.

e.g. paint coatings with lead content, contain potentially

h) At low temperatures and after a long brakes in operation it is

toxic chemical substances. In order to reduce the impact of

recommended to turn the power tool to operate it with no

these substances, the workplace must be always well

load for a few minutes to provide proper grease distribution

ventilated, and tested and safe protective measures must be

inside its driving mechanism.

used, such as safety dust filter masks with a P2 class absorber

i) Use soft, damp (cannot be wet) cloth and soap to clean power

designed especially for filtering microscopic particles. Dust

tools. Do not use petrol, solvents and other agents that may

extraction should be used, if only possible.

damage your equipment.

f) Safety goggles must always be used in order to prevent dust

j) Power tools can be stored/carried after making sure that all

from getting into eyes.

moving components are locked and protected against

g) Ear protection means (earmuffs, earplugs) must be used.

release with original devices intended for this purpose.

h) Safety gloves must be used, and the abrasive belt must never

k) Store power tools in a dry, dust and water-protected place.

be touched when in motion. This can cause hand injury.

l) Carry your power tool in its original packaging to provide

i) During operation, the tool should be held firmly with both

protection against mechanical damage.

hands.

WARNING! General warnings regarding the use of

j) Damaged, used up or heavily fouled abrasive belts must not

power tools.

be used. Damaged abrasive belts can break, be rejected and cause

Repair:

injury.

k) The der must be powered ON and OFF only when the

abrasive belt (10) does not touch the surface of processed

material, otherwise the tool can be wrenched from hands.

CONSTRUCTION AND INTENDED USE OF THE GRINDER:

The belt sander is a handheld power tool driven by a single-phase

commutator motor. It is a device of the second class of equipment

(double insulation).

The is intended for dry grinding wooden, wood-based, metal and

plastic surfaces.

Do not use for asbestos or materials containing graphite.

WARNING!

Do not use for drywall (gypsum board joints) and similar materials. Fine

BELT , detailed guidelines related to safe

dust penetrating internal parts of the machine causes blockage of

operation of the device:

ventilation spaces and leads to motor overheating and damage.

a) Belt , hereinafter called the « », is not a

The tool must not be used for works requiring the use of a

waterproof device, it must be used for dry ding only. Water

professional device. Every use of the other than the intended

penetrating into the handheld power tool can cause electrocution.

use described above is forbidden and will cause loss of warranty and

rejection of responsibility of the manufacturer for any resulting damage.

b) During operation, when the handheld power tool can come

into contact with energized power cables or its own power

Any modifications of the device introduced by the user relieve the

cord, it must be held by insulated surfaces intended for this

manufacturer from any responsibility for damages and losses incurred by

the user and the surroundings.

purpose. Contact with "energized cables" can also cause "energizing"

of metal parts of the handheld power tool causing electrocution of its

operator.

c) ding metal causes creation of sparks. Care must taken, so

the sparks created during ding do not constitute any

threat to persons, and all flammable materials must be

a) Power tools can be repaired by competent persons only who

use original spare parts. It will provide safe operation for the power

tool.

b) If a fixed power cord is damaged, to avoid risks it should be

replaced by power tool manufacturer or in a specialty repair

shop or by a qualified person.

WARNING!

While operating power tools it is necessary to observe basic

work safety rules to avoid fire, electric shock or mechanical

injury.

SANDER

Application of the tool in accordance with the intended use also refers to

its maintenance, storage, transportation and repairs.

Defective electric tools can be handed over for repairs exclusively to

service workshops appointed by the tool manufacturer. The tools

supplied from electric grid shall be repaired exclusively by authorized

san

san

sander

sander sander

san

sander

San

san

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Tryton TMT810B Şlefuitor cu bandă. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Tryton. S-ar putea să ofere un manual original. Căutați manualul dvs. Tryton TMT810B Şlefuitor cu bandă într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Tryton Şlefuitoare cu bandă
Mai multe manuale pentru Şlefuitoare cu bandă

Întrebări frecvente despre Tryton TMT810B Şlefuitor cu bandă

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Tryton TMT810A Şlefuitor cu bandă

Manual

Ryobi EBS800 Şlefuitor cu bandă

Manual

Far Tools BS 810C Şlefuitor cu bandă

Manual

FERM BSM1021 Şlefuitor cu bandă

Manual

Parkside IAN 315834 Şlefuitor cu bandă

Manual

Parkside IAN 89170 Şlefuitor cu bandă

Manual

Parkside IAN 437475 Şlefuitor cu bandă

Manual

Ryobi EBS-9576V Şlefuitor cu bandă

Categorii relevante