Manual Tryton TMT810B Şlefuitor cu bandă

Manual

An abrasive belt used for sanding metals should not be used for other allowing for easy replacement of brushes with the help of a wide flat

materials. screwdriver, and without the need for dismantling its case. After

replacement, the brush fastening caps must be firmly tightened.

NOTE: Only abrasive belts in technically intact condition guarantee good

Condition of the brushes must be inspected at regular intervals. Minimal

performance of processing and prevent damage to the power tool.

length of the graphite part of a brush is 6 mm. Operation with brushes

n Replacement of the abrasive belt

shorter than 6 mm can cause damage to the commutator of the rotor.

NOTE: Before fitting and removal of the belt, make sure the sander is

Brushes must be replaced in pairs. After replacement the sander must be

powered OFF and disconnected from the power supply.

run idle for 5 minutes.

1. Pull the belt tensioning lever (11) to the outside to unlock the

Should you encounter any technical problems, please contact an

abrasive belt (10) (see: fig. B, page 2).

authorized service centre.

2. Pull the used-up abrasive belt off the guiding rollers (13).

3. Pull a new abrasive belt (10) over the guiding rollers (13), paying

sander

attention to the direction of rotation of the abrasive belt (arrows on

the inner side of the abrasive belt) to correspond with the direction of

rotation of the sander (an arrow over the rear guiding roller) (see: fig.

C, page 3).

4. Pull the belt tensioning lever (11) backwards, to tension the new

abrasive belt.

sander

sander sander

sander

sander

sander

n Replacement of graphite brushes

The sander is equipped with external sockets for graphite brushes (8)

ENVIRONMENTAL PROTECTION:

NOTE: The symbol nearby denotes that old equipment must

never be disposed together with other wastes (with the

penalty of a fine). Hazardous components of electronic

n

equipment may adversely affect the natural environment and

human health.

Each household may contribute to recovery and reuse (recycling) of old

machinery and equipment. Both in Poland and Europe a system for

recovery of used equipment either exists or is being developed. The

system obliges all organizations that sell such equipment to collect back

the used machinery and appliances. Moreover, general purpose

collecting points for such equipment are also available

MANUFACTURER:

PROFIX Co. Ltd.

34, Marywilska St.,

03-228 Warsaw, POLAND

n

This device meets the requirements of national and European standards

NOTE! Prior to commence any maintenance or repair jobs

and safety guidelines.

make sure that the device is disconnected from the electric

NOTE! Any repair can be carried out only by qualified personnel using

power network.

original spare parts.

PICTOGRAMS:

Explanation of the icons located on the nominal plate and the

information tags.

After using the tool it is recommended to clean the ventilation openings

with compressed air to avoid damage to the bearings and remove dust

blocking the air used for cooling the motor.

- check whether the power cord (12) is correctly plugged in and the

electric power outlet is energized;

- check condition of carbon brushes and replace them if necessary.

TRANSPORT:

The must be transported and stored in its original transport case

which protects it from mechanical damage.

Adjustment of the belt track (see: fig.D, page 3)

Power the ON at low speed and check whether the abrasive belt

(10) is positioned properly. If the edge of the belt sticks behind or does

not reach the base edge by more than 6 mm, use the belt position

adjustment knob (9) to adjust the belt track.

STORAGE AND MAINTENANCE:

The requires virtually no special maintenance. The must be

stored in a place unavailable to children, in a clean condition and

protected from humidity and dust. Storage conditions should prevent

the possibility of mechanical damage and the influence of weather

conditions.

Cleaning

In order to provide safe and efficient operation, case and ventilation gaps

of the should always be free of dust and fouling, if only possible. It

is recommended to clean the tool immediately after each use.

Wipe off the with a soft, damp rug with a minute amount of soap.

Do not use any cleaning agents or solvents; they can damage plastic

parts of the .

Take care to not let water inside the device.

TROUBLESHOOTING:

The electric tool fails to switch on or works with breaks:

7

«Always wear safety goggles»

«Read this instruction before switching on the

power supply and starting the work»

«Wear »hearing protection

«Wear a dust mask»

This instruction manual is protected by copyright. Copying it without the written consent of PROFIX Co. Ltd. is prohibited.

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru Tryton TMT810B Şlefuitor cu bandă. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați Tryton. S-ar putea să ofere un manual original. Căutați manualul dvs. Tryton TMT810B Şlefuitor cu bandă într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru Tryton Şlefuitoare cu bandă
Mai multe manuale pentru Şlefuitoare cu bandă

Întrebări frecvente despre Tryton TMT810B Şlefuitor cu bandă

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

Tryton TMT810A Şlefuitor cu bandă

Manual

Ryobi EBS800 Şlefuitor cu bandă

Manual

Far Tools BS 810C Şlefuitor cu bandă

Manual

FERM BSM1021 Şlefuitor cu bandă

Manual

Parkside IAN 315834 Şlefuitor cu bandă

Manual

Parkside IAN 89170 Şlefuitor cu bandă

Manual

Parkside IAN 437475 Şlefuitor cu bandă

Manual

Ryobi EBS-9576V Şlefuitor cu bandă

Categorii relevante