Manual EGO CS1814E Ferăstrăul cu lanţ

Manual

56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS1810E 11

EN

N-2

High Brightness

Headlight Icon

PROPER GRIP ON HANDLES (FIG. O)

◾ Wear non-slip gloves for maximum grip and protection.

◾ With the saw on a firm, flat surface, hold the saw firmly

with both hands.

◾ Always grasp the front handle with the left hand and

the rear handle with the right hand.

◾ The fingers should encircle the handle, with the thumb

wrapped under the front handle.

WARNING: Never use a left-handed (cross-handed)

grip, or any stance which would place your body or arm

across the chain line.

WARNING: Do not operate the trigger switch with

your left hand and hold the front handle with your right hand.

Never allow any part of your body to be in the chain line while

operating a chain saw (Fig. P).

PROPER CUTTING STANCE (FIG. Q)

◾ Both feet should be on solid ground, with weight evenly

spread between them.

◾ The left arm should be straight, with the elbow locked.

This helps to withstand the forces generated by

kickback.

◾ Your body should always be to the left of the chain line.

INSTRUCTIONS CONCERNING THE PROPER

TECHNIQUES FOR BASIC FELLING, LIMBING, AND

CROSS-CUTTING

WARNING: Always be sure of your footing and hold the

chain saw firmly with both hands while the motor is running.

WARNING: When the saw chain is stopped due to

pinching during cutting, release the trigger switch; remove

the saw chain and guide bar from the wood, then restart the

chain saw.

WARNING: Do not pull the saw chain with hand when

it is bound by the sawdust. Serious injury could result if the

chain saw starts accidentally. Press the saw chain against the

wood, move the chain saw back and forth to discharge the

debris. Always remove the battery pack before cleaning. Wear

heavy protective gloves when handling the saw chain.

WARNING: Never start the chain saw when it is in

contact with the wood. Always allow the chain saw reach full

speed before applying the saw to the wood.

FELLING A TREE

◾ When bucking and felling operations are being

performed by two or more persons at the same time,

the felling operation should be separated from the

bucking operation by a distance of at least twice the

height of the tree being felled. Trees should not be

felled in a manner that would endanger any person,

strike any utility line or cause any property damage.

If the tree does make contact with any utility line, the

utility company should be notified immediately.

◾ The chain saw operator should stand on the uphill

side of the terrain, as the tree is likely to roll or slide

downhill after it is felled.

◾ An escape path should be planned and cleared as

necessary before cuts are started. The escape path

should extend back and diagonally to the rear of the

expected line of fall as Fig. R shown.

R-1 Felling Direction R-2

Safety Retreat

Path

◾ Before felling is started, consider the natural lean of

the tree, the location of larger branches and the wind

direction to judge which way the tree will fall.

◾ Remove dirt, stones, loose bark, nails, staples and wire

from the tree.

Notching undercut

Make the notch 1/3 the diameter of the tree, perpendicular

to the direction of falls as Fig. S shown. Make the lower

horizontal notching cut first. This will help to avoid pinching

either the saw chain or the guide bar when the second notch

is being made.

S-1 Direction of Fall S-3 Felling Back Cut

S-2 Notch S-4 Hinge

Felling back cut

◾ Make the felling back cut at least 50 mm higher than

the horizontal notching cut as Fig. S shown. Keep the

felling back cut parallel to the horizontal notching cut.

Make the felling back cut so enough wood is left to

act as a hinge. The hinge wood keeps the tree from

twisting and falling in the wrong direction. Do not cut

through the hinge.

◾ As the felling gets close to the hinge, the tree should

begin to fall. If there is any chance that the tree may

not fall in desired direction or it may rock back and

bind the saw chain, stop cutting before the felling back

cut is complete and use wedges of wood, plastic or

aluminium to open the cut and drop the tree along the

desired line of fall.

◾ When the tree begins to fall remove the chain saw

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru EGO CS1814E Ferăstrăul cu lanţ. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați EGO. S-ar putea să ofere un manual original. Căutați manualul dvs. EGO CS1814E Ferăstrăul cu lanţ într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru EGO Ferăstraie cu lanţ
Mai multe manuale pentru Ferăstraie cu lanţ

Întrebări frecvente despre EGO CS1814E Ferăstrăul cu lanţ

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

EGO CSX5000 Ferăstrăul cu lanţ

Manual

EGO CS1401E Ferăstrăul cu lanţ

Manual

EGO CSX3002 Ferăstrăul cu lanţ

Manual

EGO CS1810E Ferăstrăul cu lanţ

Manual

EGO PS1000E Ferăstrăul cu lanţ

Manual

EGO CSX3000 Ferăstrăul cu lanţ

Manual

EGO PS1003E Ferăstrăul cu lanţ

Manual

EGO CS1200E Ferăstrăul cu lanţ

Categorii relevante