Manual EGO CS1814E Ferăstrăul cu lanţ

Manual

56 VOLT LITHIUM-ION CORDLESS CHAIN SAW — CS1810E12

EN

from the cut, stop the motor, put the chain saw

down, then use the retreat path planned. Be alert for

overhead limbs falling and watch your footing.

Limbing a tree

Limbing is removing the branches from a fallen tree. When

limbing leave larger lower limbs to support the log off the

ground. Remove the small limbs in one cut as Fig. T shown.

Branches under tension should be cut from the bottom up to

avoid binding the chain saw.

Bucking a log

Bucking is cutting a log into lengths. It is important to

make sure your footing is firm and your weight is evenly

distributed on both feet. When possible, the log should be

raised and supported by the use of limbs, logs or chocks.

Follow the simple directions for easy cutting.

◾ When the log is supported along its entire length as

Fig. U1 shown, it is cut from the top (overbuck).

◾ When the log is supported on one end, as Fig. U2

shown, cut 1/3 the diameter from the underside

(underbuck). Then make the finished cut by

overbucking to meet the first cut.

◾ When the log is supported on both ends, as Fig. U3

shown, cut 1/3 the diameter from the top (overbuck).

Then make the finished cut by underbucking the lower

2/3 to meet the first cut.

◾ When bucking on a slope always stand on the uphill

side of the log, as Fig. V shown.

◾ When “cutting through”, to maintain complete control

release the cutting pressure near the end of the cut

without relaxing your grip on the chain saw handles.

Don’t let the chain contact the ground. After completing

the cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving

from tree to tree.

MAINTENANCE

WARNING: When servicing, use only identical

replacement parts. Use of any other parts may create a

hazard or cause product damage. To ensure safety and

reliability, all repairs should be performed by a qualified

service technician.

WARNING: To avoid serious personal injury, always

remove the battery pack from the product before inspecting,

cleaning, or performing maintenance. A battery operated tool

with the battery pack inserted is always on and can start

accidently.

WARNING: When cleaning the chain saw, DO NOT

immerse it in water or other liquids.

WARNING: Do not at any time let brake fluids, petrol,

petroleum-based products, penetrating oils, etc., come in

contact with plastic parts. Chemicals can damage, weaken, or

destroy plastic, which may result in serious personal injury.

CLEANING

◾ After each use, clean debris from the chain and guide

bar with a soft brush. Wipe the chain saw surface with

a clean cloth moistened with a mild soap solution.

◾ Remove the side cover, and then use a soft brush to

remove debris from the guide bar, saw chain, sprocket

and side cover.

◾ Always clean out wood chips, saw dust, and dirt from

the guide bar groove when replacing the saw chain.

GUIDE BAR MAINTENANCE

When the guide bar shows signs of wear, disassemble

it from the chain saw power head and reverse it

for reassembly (Fig. W1). This way the wear will be

distributed to maximize the guide bar life.

The bar should be cleaned every day of use and checked

for wear and damage. Feathering or burring of the bar

rails is a normal process of bar wear. Such faults should

be smoothed with a file as soon as they occur. A bar with

any of the following faults should be replaced.

◾ Wear inside the bar rails which permits the chain to lay

over sideways.

◾ Bent guide bar.

◾ Cracked or broken rails.

◾ Spread rails.

In addition, the guide bar has a sprocket at its tip (Fig. W2).

The sprocket must be lubricated weekly with a grease syringe

to extend the guide bar life. Use a grease syringe to lubricate

weekly with chain oil by means of the lubricating hole (Fig. W3).

Turn the guide bar and check that the lubrication holes and

chain groove are free from impurities.

W-1

Sprocket in Guide

Bar Tip

W-2 Lubricating Hole

NOTICE: Use EGO authorized lubricants for best results.

TRANSPORTING AND STORING

◾ Do not store or transport the chain saw when it is

running. Always remove the battery pack before

storing or transporting.

◾ Always place the guide bar sheath on the guide bar

and chain before storing or transporting the chain saw.

Use caution to avoid the sharp teeth of the chain.

◾ Clean the chain saw thoroughly before storing. Store

Evaluare

Mai multe despre acest manual

Înțelegem că este plăcut să aveți un manual pe hârtie pentru EGO CS1814E Ferăstrăul cu lanţ. Puteți oricând descărca manualul de pe site-ul nostru web și îl puteți imprima singur. Dacă doriți să aveți un manual original, vă recomandăm să contactați EGO. S-ar putea să ofere un manual original. Căutați manualul dvs. EGO CS1814E Ferăstrăul cu lanţ într-o altă limbă? Alegeți limba preferată pe pagina noastră de pornire și căutați numărul de model pentru a vedea dacă îl avem disponibil.

Specificații

Toate manualele pentru EGO Ferăstraie cu lanţ
Mai multe manuale pentru Ferăstraie cu lanţ

Întrebări frecvente despre EGO CS1814E Ferăstrăul cu lanţ

Echipa noastră de asistență caută informații utile despre produs și răspunde la întrebările frecvente. Dacă descoperiți o inexactitate în întrebările frecvente, vă rugăm să ne anunțați utilizând formularul de contact.

Produse asemanatoare

Manual

EGO CSX5000 Ferăstrăul cu lanţ

Manual

EGO CS1401E Ferăstrăul cu lanţ

Manual

EGO CSX3002 Ferăstrăul cu lanţ

Manual

EGO CS1810E Ferăstrăul cu lanţ

Manual

EGO PS1000E Ferăstrăul cu lanţ

Manual

EGO CSX3000 Ferăstrăul cu lanţ

Manual

EGO PS1003E Ferăstrăul cu lanţ

Manual

EGO CS1200E Ferăstrăul cu lanţ

Categorii relevante